I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
I am designing a custom board for the NRF9160 following the 91 thingy as reference.
I will operate only in US and Canada. I noticed that multiple matching circuits have...
Using ncs v1.4.0, modem FW v1.2.3, SES v5.10d. The code is based on the Asset Tracker, LTE with PSM, motion-activated GPS, using MQTT to send GPS location to backend.
prj...
We are trying to upload Bootloader only, but it fails with 'Error 5: FW version check failed'. Please view log / pictures.
We have tried to change the bootloader version...
Hello,
there is the following page:
https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library/blob/master/documentation.md
Known issues
Since iOS 13.3 (?)...
Hi all. I've seen a few posts about this, but none of them seem to have the knowledge I'm looking for. I am helping plan a device that has two units and will connect to a...
Hi, guys.
I'm using nRF52 DK (PCA10040) and 16x2 LCD ( ST7032i ). I would like to create a custom icon (e.g. degree Celsus ℃). Here is my code. It doesn't print anything...
Hi,
I would like a solution for encrypted OTA firmware update and I just realized that the Secure DFU doesn't enrypt the firmware image just sign it.
I find this Q&A:...
Is there a way to change the Thread SDK example program (\examples\thread\ncp\ftd\uart) baud from 115200 to a higher 460800? If so, what steps are needed to make this change...
With SDK For Mesh v5.0.0 the replay cache is saved to flash using MESH_CONFIG_STRATEGY_ON_POWER_DOWN. In mesh_config_load() a check is made to ensure that there is enough...
Hi,
I'm working on porting BG95 to nrf52 sdk, it'd be a lot helpful if I can get a head start with some open source implementation(AT parser libraries, drivers porting etc...
Hi,
In the Product Specification for nrf52840 it´s written that setting CONFIG (0x50C) register to Pause (0) would pause the watchdog while the cpu is halted by a debugger...
nrf52840 with SDK15
I am trying to update 3 characteristics if the correct value is written to an authenticated read write characteristic. Actually all of my characteristics...
I'm trying to create a simple point to point link using the nRF24L01+ with a new non-arduino microcomputer. I've searched the internet for example Python programs but only...
Hi,
I would like to double check with you if 9-pin cortex-M adapter board for Jlink can be used and connected to PPK P21 connector : https://www.segger.com/products/debug...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using internal flash one of the sector with start address of 0xfc000.
We have written...
