Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi, I am using nRF24AP1 for ANT+ purposes and I am looking for continuous scanning mode (the radio is active in receive mode 100%). The command Open Rx Scan Channel (0x5B...
when I have the line in my sdk_config.h, it overrides the and I end up with undefined reference errors.
right now I had to comment out the line to be able to compile the...
Hi,
I need to print the RSSI value to the nrf app or putty terminal to check the RSSI value.
I have gone the structures "ble_gap" file to get the RSSI value and calling...
Hi everyone
The following code is initiaizing the uarts correctly,but there is unpredictable behaviour in this case.
Whenever i disable the 1 UART sensor, works fine....
Hi all,
I am very new to the field of BLEs now I bought one BMD300 Evaluation board,and I want to use nRFgo Studio for the development is it possible to use nRFgo Studio...
Hi,
we are using nRF52832 ADC in differential mode. We have two channels connected, where other is presenting reference voltage 1,65V and other is +/-1,15V on top of that...
Hi. I am developing based on the multi-link central example. In the below code the PHY is set to BLE_GAP_PHY_AUTO.
I don't know if my example therefore is running at 1Mbps...
I saw several threads that talked about this, but I could not decipher an exact answer, so apologies if this is a Re-Ask.
I recently purchased a nRF52840 Dongle with the...
I am not able to Control GPIO PIN 14 In this program(BLE_UART) this PIN gets powered continuously . When the device connects to NRF App the power supply becomes Zero and after...
Hello.
Im in a stage where I need to transfer over our current old (ancient) libraries for SPI communications to a NRF52, where we use SPI to communicate to a certain slave...
Hello,
I have set up the Development Kit according to the following instructions and successfully activated the SIM card.
www.nordicsemi.com/.../GetStarted
Unfortunately...
Hi Everyone, Please help me understand what will be the average current consumption per hour with nRF52810 if I transmit 50bytes of data 4 times per hour and go to deep sleep...
Hi,
I'm using nRF52840 and SDK 15.2 and want to realize a proprietary radio.
I tested the ESB (enhanced shock burst) example and it worked quite well. Next I tried to...
Hi,
I was wondering if you had NRF9160 examples for a HTTP client?
I'm a bit lost with the 9160 SDK and its 4 examples having been used to such a rich set of examples...
