nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi,
I have my custom board wired to the nRF52 development board. I am using SDK 15 and softdevice 132 for this. I am trying to set up SAADC to measure adc data on Analog...
Hi,
I'm only seeing the GPS_SIM driver in the nRF Connect SDK. Is there any driver to enable any evaluation of the nrf9160 on chip GPS anywhere?
Regards,
Kilian
Hello,
I have read numerous posts about NRF_ERROR_CONN_COUNT but yet able to solve this solve, my setup is NRF52840 Dongle as central and I want to connect to multiple Heart...
Hello all,
I am currently using the SoftDevice Handler library to enable/disable the SoftDevice and observe requests and state transitions on nrf52832 with SoftDevice S112...
I need maximum throughput in nrf52832. So i enabled DLE and using s132_nrf52_5.0.0_softdevice. The data packet length is 96 bytes in single packet. Conn interval 7.5 and 10ms...
I Can't set nRF5 SKD Root Path to: nRF5SDK=C:/nordic_semi/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96
I created a global macro as instructed (many times) but the path...
Hi there!
I'm using nrf9160 DK's SiP to establish TLS connection to MQTT broker.
When I call nrf_inbuilt_key_write it returns 13 error code which means "If the operation...
Hi everyone.
In mesh light switch example., i try to add timer0 (or any timer).
After initialize timer, application always jump to timeout event, and i don't know why...
I am developing based on ble_app_uart example of SDK12 for nRF51 DK and I need to switch BLE off completely when power disappears to save battery and switch back on when power...
After reading the document for nRF52840 Radio Peripheral. I have a doubt about LENGTH field in packet format. what is the difference between LENGTH field and STATIC_PACKET_LENGTH...
Everything works fine if i use the default baudrate
NRF_UARTE_BAUDRATE_115200 but if i change it to 250000 or something higher the applications starts and goes directly...
Hello ,
I want to read around 6 analog pins, not necessarily simultaneously. I could afford some delay in between them. i am using nrf52832 dev kit with sdk 15. How do i...
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.3.0/nrf/gs_programming.html#building-with-ses
I am following the example at the address below.
However, the following...
