I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I'm measuring current consumption on nRF51822, making code changes and then flashing/debugging via JLink GDBServer and gdb.
Right now it seems like I either have to physically...
Hi,
I´m using nRF51822 with my own application and I want to connect just to one specific master device (for example smartphone) after this one is bonded:
nRF51822...
Hi There,
I am developing a desktop applications (C#) using NRF2739 dongle and NRF8001 on the other side. Things were going very well using the masterEmulator.dll provided...
Hi,
How to put nrf51822 in power off mode? i simply tried NRF_POWER->SYSTEMOFF = 1; in keil but it is not going to off mode. Is there any procedure before making SYSTEMOFF...
Hello, I am using the HTS example for the nrf51822.
In the example, bond information can be deleted during initialisation by holding down one of the buttons.
In my program...
Hi sir
In Desktop 2, before BTLE pairing, nRF51 uses Connectable Indirected advertising. After BTLE pairing with BTLE host, nRF51 will select Directed advertsing for saving...
Hi to all, my first experiments with NRF51822... i compile the example projects, and everything works fine (compiling and download are ok), but looking at the code editor...
Hello,
I am using an nRF51822 Development Kit. I am trying to run pca10001/board/uart_example (with simple_uart) using the UART serial viewer built into the Keil programming...
Does anyone know how to get debug messages out to host console via SWD? I know SWD supports Serial Wire Viewer, but not sure how to get it working over GDB with JLink.
...
Hi,
I'm going to try not to get into stuff that is under apple's NDA, but my question is really on the nRF8001 side. Basically, the ANCS is a service that offers three...
I am definitely missing something here, but I can't figure out how to specify a subset of data to read from my peripheral.
Here's the setup: my nrf51822 device is a server...
Hi,
How to create new project for nordic controller using Keil
We are using pca10001 evaluation kit.
Actually in keil i open new project and select nrf51xxx board...
Dear Nordic Developer Zone,
I am trying to enable the readback protection in the main function just before the "wait for interrupt" sd_app_event_wait function using the...
Based on s110 v5.2 release note, nRF51822 will have future hardware revision.
What is the change for future hardware revision? Do we need to modify our circuit design for...