Hi,
We are using nrf54l15 soc in our product and using NCS SDK 3.4.0. The LFCLK is set to SYNTH mode where it derives the clock from HFCLK. We have a crystal driving the...
NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hi, I am running ble_app_uart_c example with a PCA10056 DK board. I modified the example to accept command from uart. Everything look OK. But when I tried to command the host...
I am trying to use an ADS1115 sensor, it is connected by I2C. And it is like this configured in my overlay file
Once I do this, the sensor shows up but with no available...
We incorporated the basic functionality of the NCS 2.0's DTM sample app inside an larger application with other threads running.
In our case, for what maps to the dtm_wait...
nRF Connect SDK 2.1.0 I strugged to get the correct PWM-frequency out with a nRF9160 (nrf9160dk_nrf9160 )dev board. ( I guess the lastest version has many changes...but we...
Dear support
I am develop another application to use DFU OTA - I have already done 1 and successful so far. I think i better generate a new key file as this is a different...
Hi,
I have successfully added nvs in my project and able to store and retrieve data in flash.
But, i can't able to write after initializing mesh.
Could you guide me...
Hi,
we are using nrf9160 custom board we need to see log but in my custom board design we don't have UART so, how we can able to see the debug logs
Is it possible to see...
Hi. I'm using nRF52832 (SDK 15.0.0)
Recently, I'm merging UART and twi sensor examples and I have this kind of error.
This above capture is about twi sensor. I have...
Hi,
I am trying to integrate DFU into my application. Below is what I need to do.
I receive OTA application image over BLE (I can not use legacy DFU feature as we are...
Hi, we're planning to connect the nRF5340 (running Audio SDK in gateway config) via I2S (and UART) to a custom device. We need to configure the nRF5340 be I2S slave even though...
Hello,
I am looking for an RSSI example, using the dev-kit nRF52DK. To start off, I will have two dev-kits and measuring the range between the two units. After that I would...
Hi,
I'm using an nRF52840 on a custom board with nCS 2.0.0.
The board I'm working with has a serial connection to a PIC that has Ethernet, so I'm trying to use that as...
Hi
Mesh DFU shows New firmware message after DFU update and gets stuck in the DFU mode. I have assigned different application id to all the boards.
Right now I am using...
Hello Sirs
I want to use the SPI hardware of nrf5340 in my custom board. I want to communicate with ADXL362 which is a very low power movement
sensor. Is there any similar...
