Hi,
We are using nrf54l15 soc in our product and using NCS SDK 3.4.0. The LFCLK is set to SYNTH mode where it derives the clock from HFCLK. We have a crystal driving the...
NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I have just spent a few weeks of work developing an application with NCS (2.0.0) for the second-biggest chip of the nRF52 series, the nRF52833 . Now I have tried to activate...
Hi Community
I am a physical therapist, developing IoT devices for sports tech.
Any suggestions for Nordic products that can do Hall Effect sensor IoT to device.
I'm...
Hi,
My custom board using P0.23 as a PWM output to control a PWM fan. It works properly when the firmware is running.
But I noticed that when flash firmware using JLink...
Hello,
Is it possible to display the actual time in PPK2, rather than just a generic timestamp? This would make it much easier to sync with other test loggers connected...
Hi,
I am using nrf52840 DK to try out the image transfer service and its capabilities but unfortunately, I don't have the camera. I was trying to turn the image into a hex...
developed a product using the 9160. Now I need to upgrade the SDK from 1.2.0 to 1.9.0. During the test, I found that the servers that could be connected normally in the past...
I was trying various things to get my application to build when, suddenly, nRF Connect began giving me this error when trying to create a new build configuration. Here's the...
Hello
My application is based on the Distance measurement sample which uses a BLE scan response callback to trigger the measurement synchronization sequence in reflector...
Hello,
I have an NRF52840 and I was wondering if I wanted to save IMU data to storage on the microcontroller, would that be better on flash or eeprom, as from what i know...
Nevermind. It appears this problem went away after I opened up several system files including the one you mentioned, then recompiling.
Using
Keil/uVision MDK-Lite V5...
I have built and flashed the NUS example in the SDK and using nRFConnect on my phone I can send data to the dev board. However, I am unable to receive data at nRFConnect sent...
Hi,
I made a BLE module with nRF52840, but an error occurred when testing DTM.
I have successfully compiled the project, but when I use nRF Connect-Direct Test Mode...
Hello,
after importing the dfu_buttnoless service in my application, I'm experiencing a strange issue with the advertising info between release builds and debug builds....
Dev tools: HW: nRF52DK_52832 (& LTC DC1697A) SDK: v2.2.0
The problem: The I2C transfer function doesn't work as expected within a callback.
Steps to reproduce: 1. Starting...
