NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hello,
I am using a custom app that uses Nordic's DFU library to update my device.
It works most of the time but for some users, the process fails about 4 seconds after...
Hello,
I'm trying to run a simple example setting the RTC1 in a nRF52840-DK, but I'm having some issues.
Here is my prj,conf and code:
The idea above is set the...
Hello,
For my project, I would like in my Thread Network that the children of the routers can communicate with their parent with a local scope (that the messages are not...
Hi,
I have designed a hardware with NRF52840 and i connected VBUS pin for future operation. Now i want to disable reset to disable wakeup from SYSoff mode by VBUS rising...
Hello - I am evaluating secureboot on the nrf9160. I have followed your very-good secure immutable bootloader example - and I can see from the serial output the image is verified...
Hello,
I am trying to compile a legacy Nordic Project for evaluation purposes and I am getting some compile errors. The details are as follows:
Project: https://github...
Setup :
NRF Connect SDK v1.8.0
Zephyr 2.7.0
nRF52833
Hi, in my application I am using mostly the nrfx_gpiote driver, but for one of the 1-wire communication protocol...
Hello.
I have NRF52-DK and nRF52840-Dongle.
I have custom service this large characteristics (81 byte length). I want to use AUTHORIZE REQUEST Write and Read.
I use...
Hi,
I am experiencing issues in flashing nRF52840 on a custom board I have. I have 10 boards, and only 2 work. The rest of 8 seems to have the exact same issue. At this...
I am doing a DFU on a 52811 board, and getting "SD version failure"
But I am not updating SD, and I am even getting this error when doing a DFU with the same code level...
Hello,
I have a custom nRF91 board and a SEGGER J-Link Base debugger.
I am trying to open the nRF board in LTE Link Monitor from the nRF Connect for Descktop, but the...
Hi there,
i have built a custom board in devicetree. I have based it off the nrf52840DK dts but added in a magnetometer:
s3_mini_v1.dts
i am attempting to configure...
Hi Developer Team,
I was checking the GitHub repo that sends image files to phones with the help of Arducam. My question is that, instead of connecting, can I use a non...
Hi !
I have selected sample https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/samples/bluetooth/peripheral_uart/README.html#peripheral-uart
as basis for evaluate...
During startup, I am encountering a new issue where the chip crashed out during boot. See screenshot for crash details:
"mesh_main_start()" is called from my main application...
