NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
After several resets of an application (Either soft-resets or reprogramming) the nRF9160 will fail to connect back onto the network. Currently using v1.3.4, but this issue...
I'm new to nrf connect sdk and although i studied the documentation its not completely clear to me.
What is the difference between KConfig vs KConfig.defaults vs prj.conf...
I am currently adding to the Light Switch and Light Bulb samples provided by Nordic and am confused why I cant issue commands to group 257 from the chip-tool. Everything else...
Hi,
1. Here I am using the nrf52840 in my customized board, in parallel I have nrf52840 dev board. In My custom Onboard debugger is not available so I am using SWD to load...
Hi,
nrf52832, softdevice:S132
My SPI master program can initialize the SD Card succefully.
But, when I put it into the examples of ble_app_uart on nRF5_SDK_11.0.0_89a8197...
Hello,
I will place an order with a testing company to test EN300328 emissions for a product using the nRF52840. I received an instruction from the testing company to prepare...
hello Nordic
i am working with 2 PCBs one is based on nrf52840 SOC and the other is based on the nrf52832 SOC, both PCB are peripherals that communicate via BLE with a...
Last month, everything was working. Then I just came back to continue what I'd been working on but the hardware just suddenly powers OFF after a few seconds.
Hardware: ...
Hi! We are working on nrf52833 with NVS. The devices are MITM (L3) - and therefore bonddata is saved, and an LTK used by the central for subsequent encryptions for connections...
Hi everyone, I'm currently developing a mesh network to send sensor data.
I'm stumble on a problem which is very confusing to me.
What I'm trying to do is send the bytes...
Hi, I am following this guide to implement DFU OTA onto my device https://novelbits.io/nrf52-ota-dfu-ble-part-4/ . I have gotten everything to initialize without error, but...
Hi There
I didn't realise when chosing the nrf9160 that the peripherals were all shared, to a maximum of 4 serial type devices, (any combo of i2c, spi or uart to a max of...
Hi there:
We are now successed in setting up 5340_audio (ncs 2.2.0) related demo. It will be useful for us to do more detailed investigation with BT releted shell cmds enabled...
I am looking to trigger an interrupt when Timer2 overflows. What may be the easiest route to accomplish this? I have Timer 2 set at 8 MHz, 32 Bit Length
Hi, I am new to the nordic world. I am interested in developing an application that allows me to send data via UART from an X board and read that data with the nordic nRF5340...
