We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
I have two nRF9151 DKs and want to evaluate direct, SIM-free DECT NR+ communication using FT and PT roles. Please help me with:
- DECT NR+ MAC/PHY modem firmware, rather...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
I'm working with the observer example, and in trying to make modifications to it I have looked at a couple of other projects, both online and from another product under development...
We are facing the problem that when relay feature is enabled on a mesh device (which is running nRF Connect SDK firmware), device response is delayed in a range of seconds...
I have been working on an application for the nRF5340 using version 2.1.0 of the SDK, and it includes a task which collects audio data using the DMIC driver. After adding...
I have written code based on Bluefruit nRF52 feather board in Arduino IDE. I need help to know is it possible for me to flash same code to my custom board based on nRF52810...
I am trying to get familiar with matter, and have the following two devices:
- Thingy:53 flashed with the matter weather station example ( https://developer.nordicsemi.com...
I need to send broadcast leave request to all the zigbee devices connected to the network.
zdo_mgmt_leave_req function sends leave request to a particular device but we...
We have a custom bootloader and need to set a different start address in Flash for the entire image (merged.hex)
For an earlier version of nRF Connect SDK (v1.4) this was...
Hi,
I have four Thingy:53 devices. I can get all the Bluetooth Mesh light and light switch demos to work without problem .
I would like to test and demonstrate relaying...
Dear Support,
We just discovered the hard way that the LTE link controller of NCS 2.2.0 uses the AT monitor. This is an important change compared to earlier NCS versions...
Dear everyone,
I am exploring embedded development with nRF products. In particular, I am trying to setup projects both in pure Zephyr and nRF Connect SDK (NCS) to see which...
I would like to exchange information via CoAP between my thread end devices and a CoAP server (IPv4) on the internet.
The current Setup: nRF52840 --> Border Router (RPi...
Hi,
We use nRF5 SDK v17.1.0 for custom application (bare-metal / without os). We are trying to port littlefs for External 2MB FLASH connected via QSPI.
Please let me know...
We are evaluating a product that will run as a Thread end device on a embedded Linux system. (with only Thread as interface, no wifi/ethernet)
We are today using the ot...
I have a custom board with the same hardware configuration than dongle pca10059. This board has the same bootloader than the dongle but I need to upgrade the firmware in a...
