Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello,
We are using an nRF52 DK as part of our QC process to send test commands to one of our devices and record responses. However, I think that the people running the...
Hello! I'm reading the documentation that exists for the nRF5340 and struggle a bit about the Secure attribute unit (SAU) If you read the ARM documentation about TrustZone...
Hello.
I am developing Central device which support LESC.
I have some question about connect to Servers which have diferent LE security
for example case, one of...
Hello,
I am using nrf sdk 1.5.1 and trying to connect the Nrf ZigBee router(light bulb example) with Digi Xbee Coordinator but it doesn't seem to connect. I observed the...
Hello all,
I'm interacting with some nodes in a test network:
setup: 10x nrf52840 DK (PCA10056) boards loaded with the following software.
1x Coordinator ( Zigbee CLI...
Hello,
I'm using nRF SDK v1.6.0 with nRF9160 development board. I did minimum changes to Asset_Tracker_v2 application (enable debug log, set up for my aws account and to...
Migrating from nRF5 SDK to nRF Connect (Zephyr) what is the best way to define pin names using a custom board? in nRF5 SDK the header file custom_board.h usually defines the...
If I enable CONFIG_ASSERT=y this example will crash (or code using the DF APIs)
To reproduce:
- nRF Connect 1.6.1
- In direction_finding_connectionless_rx add CONFIG_ASSERT...
HI Devzon
currently my customer has some question about the power consumption difference between "LOWLATENCY" & "LOWPOWER" on NRF5340 GPIOTE
we useing PPK2 to testing...
hi support team，
customer have one problem that saadc is high rate sample at about 800hz, it runs ok, but after ble connection and send data to device from mobile device...
Hi , My application works on ncs v1.3.0, and now I need to upgrade the SDK to upgrade the application to work on ncs v1.5.1. I have completed the application development on...
Hi,
I am developing a PCB with the nrf52840 chip. The chip is implemented as described in the datasheet ( Circuit configuration no. 6 for QIAA aQFN73 ), using the files...
We are encountering a very strange situation. We have two custom PCBs (PCB1 and PCB2) both with an NRF52832. We were able to program both PCBs (multiple times) with the JLink...
Hi
I'm trying to file open and write for logging temperature data and others on nRF52840.
I successfully open, read and write on SD card or flash in nRF52840.
I also...
I am looking for technical support on Nordic Chip NRF52805 chip recommended footprint – BGA pad size.
Based on the application note on WLCSP Package guidelines from Nordic...
