We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hi,
I've stumbled upon a problem that I haven't been able to solve for an extended period of time. I've found several other posts on this forum describing something vaguely...
Hi,
I have a project that need to use a long range bluetooth communication with an Android smartphone or tablet
I use for test a tablet Lenovo Tab M8 TB8505F, NRF Connect...
Hi, before developing a BLE project, just got a general question about nRF connect on PC, does "nRF connect on PC" support Bluetooth 5 Advertising extension, if it is supported...
Hello. Developed with nrf52832 (S132 v7.0.1, SDK v16.0.0).
"pm_peer_delete" is used to delete the peer created during bonding. When I checked Flash when "PM_EVT_PEER_DELETE_SUCCEEDED...
Hi,
I have recently inherited a project from a former worker. The code intends to read data from a peripherial through TWI (the peripherial is a Si7053 digital temperature...
i used aplication twi_sensor form nRF5_SDK_12.3.0_d7731ad and i use s132.i conected mpu9060 every time get error on my terminl NRF_ERROR_BUSY.There is exemle of code main...
Hi,
I am working on a secure bootloader for a nRF52810 chip, and I am starting from the PCA10400e example in the SDK 16 and SD112 on SES (MacOS).
I successfully compiled...
Hi,
I am unable to get any programs using Zephyr to run on an nRF52840DK.
I have tried using the latest DAPlink (from GitHub) and JLink firmware (from Segger) as well...
When HFCLK was changed to "64 MHz crystal oscillator (HFXO)", the following code was implemented.
I am aware that "while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);" is waiting...
Hello all,
I would like to have some help regarding the usage of CoAP protocol. Is there any sample project that supports SDK 17.02 that I can start from?
I am using...
Hi DevZone,
Here's my setup:
Using NRF5 SDK 15.2.0, custom board based on NRF52840
Battery powered device with 3.6V battery.
Supply voltage stepped down to 1.8V...
Good day
Due to I am very new with NRF chips and I did not find direct answer on forum I require some clarification on that moment...
The task is to detect input pulse...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
As mentioned in the DK board User guide nRF52840_DK board is preprogrammed, so, till now we didn't flash the DK board.
I tested the nRF52840_DK board using J2 USB connector...
