The EdgeAI documentation includes a required piece of hardware for use with the nRF54LM20-DK when implementing the gesture recognition sample, specifically the " pca63568...
I'm aware of https://devzone.nordicsemi.com/f/nordic-q-a/125252/reset-over-ctrl-ap/555253?focus=true
Is it possible for an nRF54 to safely use the CPU access to the AP registers...
Hi,
Sorry, I found a similar question on this site, but I still don’t understand. We would like to demonstrate the following.
Perform distance measurements simultaneously...
Hi support team,
We would like to evaluate channel sounding using your evaluation board.(nRF54L15-DK and nRF54L15-TAG)
We have been able to verify channel sounding using...
Hi all,
I want to ask which silicon version are the DK stocked at Mouser or DIGIKEY for the product nRF52LM20-DK. Is it version 0.7.0? Thanks!
2.16.1.2
2.16.1.2
2...
Hello!
We have a nRF52832 firmware project on NCS v3.4.1. After recently moving from NCS v2.9.0 we saw small current spikes every 1s (roughly) in our idle state, which weren...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hello
I have a very strange problem
A custom nRF52840 board has a charge detect pin, P1.6
A gpio callback is installed to wake it up on charger connect/disconnect
...
I was wondering if there was a way to use the Nordic Power Profiler Kit II (PPK2) as an ampere meter, and be able to determine more details about what portion of the current...
Hi Noridc expert ,
I am trying to configure using nsib + mcuboot on nrf52840,
I need to build the image with only public key avaliable , and sign the image else where...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hello! I've been trying to do the same project for about a month now - just a simple keyboard adapter that takes the input from a keyboard and translates it into HID signals...
Hi,
Is it possible to advertise legacy (without extended mode) and coded simultaneously, and both connectable?
I see the sample from nRF Connect SDK, multiple_adv_sets...
I’m writing BLE UART code. When BLE is not connected, current consumption is ~30 µA. But when BLE is connected, consumption increases by ~1 mA. I want to reduce the current...
Hiya,
I was testing with USBD MSC, using fatfs (exFAT) and was hoping to inquire about a reasonable expectation when it comes to transfer speed.
My current setup is as...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Hello,
I’m trying to run the TensorFlow Lite Micro example (zephyr_samples/hello_world) on my nRF5340DK using nRF Connect SDK 2.6.1, but I’m unable to build the project...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
