It flashes with sucess
C:\Users\vasco>openocd -f interface/stlink.cfg -f target/nrf52.cfg -c "program \"C:/Users/vasco/OneDrive/Ambiente de Trabalho/zephyr.hex\" verify...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
I'm looking for some additional information about the Assisted GPS functionality in the nRF91.
Exactly what is it?
How does it work?
Is it available with the current...
Hi,
I have an application that does HTTP requests to a backend server. I'm now working on implementing TLS for encryption of the data.
Are there any examples of doing...
Hello everyone,
we are developing a bluetooth application based on the relay example included in SDK 14.0.0. We have already developed our own services and characteristics...
Hi,
I've been searching for a LSM9DS1 driver compatible with the nRF5 SDK >= 14.0 but I couldn't find any which uses the nrf_drv_twi so I started to write my own but it...
Hi All,
I'm working on minimizing power when transmitting a small message between two nRF52832 boards. I'm also trying to maximize range so sensitivity is important.
I...
Please ignore, this is test post. The SES project in Thingy:52 SDK seems to be broken, I get a lot of error trying to compile. What can I do to fix it?
Hello,
I have an application that requires an always running ADC to sample three channels at 4096 Hz. I have successfully adapted my application from the many examples posted...
I am working on Flashing Code into Nordic nRF52832 using SWD Protocol.
We have achieved 80% SWD in communicating and flashed code into Nordic and verified all is working...
I would like to confirm what I'm seeing on my setup trying to measure current with the nRF9160 DK.
I'm using an oscilloscope and am following the instructions in the latest...
If I were to design a product using nRF52840 & Thread. Normally, I would have to certify the product with the thread group and become a member. The thing is: - the product...
Hello,
I am developing a remote device which uses system off mode for idle state. I also have the condition where extra long press of any key that is beyond the long press...
My Peripheral is using the ble_conn_params module. I'm seeing that if my Peripheral calls sd_ble_gap_disconnect() soon after making a connection, the module will sometimes...
To the kind attention of Nordic support team,
I'm studying documentation in https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v5.x.x/doc/5.2.0/html/a00140.html where it...
Recently I check back again into att_mtu_throughput example in SDK 15.2. there seems to have some updates than in previous SDK, and I see this BLE_GATT_EVT_DATA_LENGTH is...
