Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hi All,
Is it possible for me to broadcast multiple&different type of beacons/advertisement, for example ibeacon, eddystone, unconnectable-advertisement, connectable-advertisement...
Hello, I would like to use the pc_ble_driver_py with sd api v6. I can see in the CMakeLists.txt where I can change set(SD_API_VERS "2;5") to set(SD_API_VERS "2;6"), and it...
Application Info:
I am working on developing a synchronized mesh network of low power sensors. I am trying to maintain an average power consumption of 100's of µW while...
Hello, there,
I am trying to get the UARTE working on a custom nRF52840 board. In my setup, I am expecting a response to every transmission on UART.
Here's my setup...
Hello,
Would appreciate current-day thinking regarding unused GPIO pins. Our product uses Laird's BL652, which embeds the nRF52832. Many GPIO pins are unused. I've looked...
I am new to nRF9160 development board. I have just opened the board and tried to connect following the startup instructions. I was able to see LED 3 and LED 4 blink the first...
Hi,
I am trying to get a bootloader to work on the nRF52832 and struggling to get the application to run after a DFU. I could not get this to work on my custom board and...
First of all, thank you and kudos to Nordic Support Team for having an awesome and functional forum.
Having said that, I have a question related to the architecture of mesh...
Hello,
I am trying to analyse my project my source code with sourcetrail (give graphics with calling functions).
During indexing task, some libraries are not found like...
Hello,
When I run the ble_app_template application from the examples, sd_app_evt_wait() cause an error and the app to crash. So I've put my project in debug mode (DEBUG...
After successfully running the GPS and acquiring position the application goes into an infinite wait loop when attempting to start it again, but only if either or both of...
Hi all,
I upgraded my Sony Xperia XZ2 Compact to Android 10 recently and am no longer able to find BLE5 devices using advertising extensions in nRF Connect (or any other...
Hi,
I know that many people ask this question on different posts but I was not able to find the right solution for my case.
I am observi ng an average current of 4.7uA...
Hi Nordic-Team, I would like to setup a testbed that should be used to measue/evaluete the power consumption of a nRF52840-DK with a connected secure element (like OPTIGA...
i am using winc1500 for wifi connections , i tried through uart too but it doesn't work . Now i want to execute thrugh spi any example or githib code is available
