I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi.
I am using nrf52832, SDK15.0.0, and S132 SD.
I am using a custom board.
I checked the consumption current of 80uA in system off sleep state.
I want to lower...
First some general info:
* Compiler GCC 7.2.0 GDB 8.0.1
* VisualGDB 5.3R8 Build 1973
* Visual Studio 2017
* SDK 12.0
I try to build an application using the SPI...
I can play with at client and asset tracker demo with my SIM card but I don't know the network type of my SIM card. Can anyone tell me how to determine Cat-M1 or Cat-NB1 or...
Hi,
I am using S130 on an nRF51822 with SDK v12.3. I want to handle the different error codes that could result from calling sd_ble_gatts_hvx and retry later.
Firstly...
Hi,
we've developed and produced a nRF52832-based custom PCB with custom firmware that is using advertising, scan, connection, custom Bluetooth service and characteristics...
Hi there,
I am designing my own custom nrf52832 PCB and would like to have my design evaluated before put it to production. I am just wondering if Nordic Semiconductor provides...
I am running SDK 15.2 on an nRF52840. I have programmed my secure dfu bootloader, application, settings.hex, and softdevice via jtag. During the first run after programming...
Dear fellow developper,
I'm trying to create a BLE device using HID service to control music, volume and so on.
I have successfully implemented a keyboard + Consumer...
Hello,
I would like to know if anyone else has faced this issue. Indeed, if i want all the consumer control interpreted in the right way, i need to add a keyboard in my...
I'm working on a project with nrf52840 and i'm trying to send and receive ipv6 packet throw thread protocol so i tried to use to send with otIp6Send and receive with otIp6SetReceiveCallback...
Hi,
We are currently working on a project involving a few Connectionless BLE advertisement transmitters based on nRF52832 (SoftDevice 6.1.0). On the receiving end we have...
Hello
I m hardware designing engineer in Turkey.
I m designing bluetooth controlled lighting armature. it must be connect other lamps. And must controlled by phone ios...
