Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi,
I am adding BLE functionality to one of my existing product. I product will play the central role for which I am thinking to use nRF51822 based module.
I learned...
Hello i read RSSI in beacon_evt_handler() hrs_scanner project:
printf("RSSI: %d\n\n\n",p_evt->rcv_adv_packet.adv_data.rssi);
but he show me a wrong value of RSSI: 4539...
Hello, I connected, according to official layout design, a 32 Mhz crystal to my nrf52840. Using a 60 Mhz oscilliscope, I decided that the crystal isn't working (no sine wave...
Hi all,
I'm on 10.11.1 (El Capitan), followed the instructions here
github.com/.../pc-nrfutil
And it looks like installed was happy but when I try and run nrfutil...
Hello,
While porting a C++ application to SDK13.0.0, I ran into weird compiler errors, such as
error: #800: this declaration may not
have extern "C" linkage
...
Hello,
I am using a nRF52832 DK(PCA10040). I am qurious about the output impedance at RF connector "J1" on the PC board. Does it provide 50 ohm output impedance so we can...
Just two questions regarding the new nRF52840 to make sure I've understand it correctly;
For the NFC, this is passive only? So it acts like a tag and is not able...
I've been trying to for two days. Using nrf52DK, SDK12, no SD, Keil5.
All I want is to get printf() to work over ITM/SW/Debug, I'd even accept RTT if I had to. I can't...
Hey I am trying to create a blinky project from scratch on
System: MAC OSX
Eclipse Neon
GCC 4.9
I am trying have it eclipse managed make.
I am at a point when after...
Hi, I was wondering If I need to wait for a response from the server that a command was executed before executing another command or if the BLE stack takes care of this under...
Hello
i m searching for a method to send a big buffer with TWI to a slave. The Buffer is read from flash. because its a soundfile its needed to send the buffer without delay...
I am trying to set up a nrF52 -> Rpi v3 -> Exosite through CoAp as in the nrF5 iot sdk. The nrF52 to rpi works as I am able to ping the nrF52 through its global link address...
Hi,
I am writing a code base on the reference manual of nRF51422. In section 29, UART, I don't understand the differences between TASKS, EVENTS and REGISTERS. Aren't they...