Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Is it possible to support both LE Secure Connections Just Works pairing and Legacy Just Works pairing in a single device?
My concern at the moment is that if I require...
I have one problem with unsing uint64_t in application...
Im for test try simple demo:
uint64_t test = 1327644190303473294;
NRF_LOG_INFO("test: %"PRIX64"\n", test);...
Hi,
i am using nRF51822 EK with soft device s130_nRF51_2.0.0(id:0x0080) and nRF5 SDK v12.2.0 and keil u vision5.
when trying to flash TWI sensor example programme (nRF5...
Using nRF52DK and working through the getting started tutorial I could not get the ble_app_uart example in SDK 12.2.0 to work. It compiles without errors or warnings and appears...
Hello,
Trying to make my own project to test buttons and LEDs for educational purposes, I looked at this . Using uVision, I tried to replicate the included modules of that...
i am testing the ble_uart programme. i am using the nRF51822Ek and soft device s130_nRF51_2.0.0 and nRF5 SDK v12.2.0 and keil uvision5 and nRF tool box (android).i am using...
Hi
I have the PPK, and I see it needs either a JLink or a Nordic DK board to act as the interface to the PC.
I have a nrf52832 dk and also nRF52840 dk, so I was going...
I made IAR work with nrf52 in monitor mode debugger. I also would like to try this to nrf51. I found nrf51 doesn't have DebugMon_handler......Please confirm can I single step...
Hi,
I am working with nRF51 for my application. I do not use softdevices. I need to have a random variable in my code. I have read Reference Manual and I have found that...
Does nRF51822 have battery monitor?
pg 45 of datasheet says specifies "Absolute error when used for battery measurement" at:
Internal reference, input from VDD/3...
In the nrf52 OPS datasheet, for NVM and flash programming electrical specification (page 41) it has "Amount of writes in a block between erase" and Minimum for that is 181...
Hi all.
I need some suggestion how to use UART module in the nRF52 using nRF5_SDK_12.2.0 and the softdevice $132(it would affect?)
I would like use RX to receive information...
Hi.
Didn't find an exact answer for my question.
I'm using the ble_app_beacon example on my custom board based on nrf51822. While powering it from a coin battery, I measure...
Greetings. This is a followup to my previous question BLE Software Configuration for FCC Spurious Emissions . I did not ask the right question there and I did not want to...