We are seeing the same thing as in 129099 (case 362913) and 129410 , found independently on our side. We have narrowed it down a bit further, so we open a new thread with...
We are investigating an intermittent Bluetooth Mesh LPN issue on the nRF54L15, where the LPN state machine becomes stuck in BT_MESH_LPN_ESTABLISHED even though the Friendship...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hi,
On the nRF93M1 DK, we can switch between physical SIM and eSIM with %SIMCFG="SimSlot" (mfw 1.5.0).
1. Is SimSlot written to NVM on set, or in the flush at CFUN=0?...
Hello, I've built sample aws_iot for target nrf54l15dk/nrf54l15/cpuapp, using the provided .conf & .overlay files for nrf54l15dk using NCS 3.4.1. The certificates and keys...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
Hi,
I’m having some troubles with example code : ble_app_uart_s132_pca10040. The code compile well in Keil and I can prog it in the nfr52 but it doesn’t run. When I check...
To enable comparability with an existing client, I'm attempting to configure the nRF51822 to provide a GAP service that includes user description descriptors (UUID 0x2901...
I'm trying to store some values with fstorage. The store operations seem to be queued successfully, but never executed. I currently have this to test the behavior:
FS_REGISTER_CFG...
Hallo everyone,
I am reciving a notification from my server, which lenght can be 8, 20, 30 bytes but when I want to display the info using NRF_LOG_INFO is not printing...
To All,
From reading the datasheet I understand that nfr52832 spi can only send/receive up to 255 bytes at once. And to work around this a list method is used.
Because...
Hi,
I’m working on a device that requires to enable the softdevice when connecting with a smartphone via Bluetooth and disable it when acquiring data from an analog source...
Hello,
I am using sdk12 and uart code. I want to send my sensor data readings to ble app. For that I have modified the ble_app_uart code and I am able to send 8 packets of...
Hi all,
In my project I have a structure its length was about 2KB, I'm saving it as a static variable after using this I come across with a weird behavior from the board...
Greetings,
I'm having trouble being able to perform a DFU with the secure serial DFU. My setup:
Using PCA10040 (nRF52832) with the s132_nrf52_4.0.2_softdevice.hex...
Hi.
I am using saadc sample cod of SDK13. Changing some parameters based on the analog input, the example is sucking somewhere where I have not been able to find it.
...
Dear all,
I am facing small problems, which I guess most of you faced at some moment.
I am trying to switch from working with ST microcontrollers to working with nRF52...
Hi,
I know that the default handle value of device name is 3, but in my application i am not getting the default device name handle, is it possible to change the device...
I want to save precious CPU cycles by writing 40 i2c (TWI) registers in one shot. Can I somehow set up the TWI master to write 40 registers (each 16-byte address with 8-bit...
What is the maximum length of pdu for ble advertisement? I have ported the example application of solar powered beacon without softdevice.
I just wanted to know if it was...
