Hello,
I am trying to debug a basic test project and using the "Debug with Ozone" button in the nRF Connect for VS Code extension. I am using the nrf54l15dk board for development...
Hello, Looking at the already opened questions, there seem to be some similar questions asked when migrating to the DTS partitions, but i haven't found the answer on specific...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
Hi Nordic
Our project is preparing for mass production and we've encountered an issue while designing the flashing solution. Our project is based on the NCS 3.3.0 single_slot...
I'm onboarding an nRF9160-DK to nRF Cloud for CoAP A-GNSS using nrfcloud-utils, and every CSR-parsing step fails with the same ASN.1 error at the CSR's signatureAlgorithm...
Hi DevZone Support.
We've been impressed by Nordic's Edge AI Lab & sdk-edge-ai addon and are looking to use it's models & runtime in our products.
Based on the documentation...
When performing a OTA update with RPA enabled, the dedicated DFU app, nrfconnect app, and nrfutil.exe fail because after the buttonless bootloading has been enabled the device...
Hi,
I'm building a device with an nRF52 or nRF51 Module (still undecided), but still need a second MCU for USB Host functionality. Unfortunately, USB Host requires a precise...
I modified the nRF51 SDK_v5.1.0 .36092\Nordic\nrf51822\Board\pca10001\s110\ble_app_hrs proj and downloaded to my self-made pcb,and it worked well. Then I want to update to...
Hi there,
I'm using an input GPIOTE based on SDK11. The interrupt is consistently being fired. On the other hand, if I use "if(Pin_6)" to check the trigger, it does not...
I am trying to use SEGGER_RTT_printf with SDK12 in eclipse.
I have added the appropriate lines to the makefile and SEGGER_RTT_WriteString works fine.
My Makefile lines...
I followed this blog entry ( devzone.nordicsemi.com/.../) setup IAR to debug in monitor mode (by adding Jlink_monitor.c, jlink_monitor.h, jlink_monitor_isa_iar.s, add EnableMonMode...
Hi,
In our project we need to store data onto the internal flash memory.
The data that's stored will be transferred and modified via "BLE uart service". When I tried...
Hi guys,
I'm working on an nRF52832 chip (PCA 10040) with softdevice s132 (v3.0.0) and I'm facing with a big problem; in my project I use an spi (instance index 0) and an...
Hi,
we have the need to develop an application that needs a precise second counter over time.
Our firmware is using the S110 SoftDevice (v8.0.0) and SDK v8.0.0 to perform...
Hi!,
I'm trying to compile GitHub examples, for example this github.com/.../nrf51-ble-tutorial-service
I cloned it into nRF5_SDK_12.1.0_0d23e2a/examples/peripheral....
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
Hi
We are using "gcc compiler" to compiler our programs. To download our programs we use "nRFgo Studio" app.
From the above image, when we load SDK into the device...
Hello,
Consider this scenario:
The client successfully writes to a characteristic by the application code can't use the data sent so it would be usefull to signal the...
Hello,everyone. Now i have the board nrf52832 and i want it to enter the low-power mode but keep the the advertising. Now the measured current is 160uA, I think there should...
Dear All,
I apologize in advance if it seems that the question has been already posed but it is still unclear to me.
I have a pin (SIG_OK) and I want to read its logic value...
