Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi, I would like to consult how could I deal with this error and build the code succesfully.
In device.h
'__device_dts_ord_113' undeclared here (not in a function); did...
Hi guys, I am creatiny encryption with nrf9160.
I managed to do CHACHA20-poly1305 and ECDH
But now I am trying to pass ECDH Master key to HKDF-SHA256 to generate a temp...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
I use a NRF52832 with SDK15.3 S332,
#define NRF_SDH_BLE_GAP_DATA_LENGTH 251
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247
When my device as a periph sending data to the...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
hi,
i have successfully entered the dfu mode many times and could change the applications and reenter the DFU mode.
But then i tried loading the softdevice at "nRF51_SDK_8...
Hi, All,
I am currently developing with nRF51822AC. Due to some issue, we would like to replace the current 16MHz crystal with a crystal other than this frequency. We would...
softdevice 8.01 s110
device nrf81522
hts example,add three ch adc,lcd eg.
phone : HTC one M7
app:nrf tools HTM
when try to connect the device by BLE, when recive the...
Hello!
I am trying to run example uart project (uart_pca10028) on PCA10028 development board. When code is loaded to the microcontroller it signalizes error - all leds...
Hello All,
I am working with a pre-programed PCB; the main components of the are a nRF51822 chip, a GPS, and a GSM. I am using a J-link to communicate to the entire board...
Hi,
I have a BLE thermometer I want to snif using nRF-Sniffer and Wireshark.
Unfortunately I'm unable to sniff the data, I only see the initial "hand-shake".
Process...
Hello,
I have the nRF51822 evaluation kit, the Keil MDK software and a custom board with the nRF51822 microcontroller on it. My question is if it is possible to use the on...
Hi I am not sure on the nRF51422 chip the iBeacon function is fully supported, is it ?
I can make the examples working on it but on the Nordic site only on the nRF51822 chip...
Hello,
we are trying to avoid using code that triggers hardware issue #39 in the nrf51822, which appears to be fixed in chips whose build code is Hx0.
We would like...
Hi,
I'm currently developing a firmware running on nRF51-dongles (PCA10028). The dongle communicates with a PC application over UART. Everything is working fine except...
Hello we would like to use the Nordic chip to send wireless messages from a node to other nodes directly,without hubs. We wouldn't like to be limited to up to 8 nodes receiving...
Hello,
Setup: Android 4.4.2 (LG G2), nRF51822 peripherial.
I noticed that once in a while when trying to connect to my nRF51 based device it won't connect and what is...
