I would like to test updating my Matter device based on the nRF5340 using the Matter OTA.
I am reading the documentation here:
https://project-chip.github.io/connectedhomeip...
When custom board with nrf52840 uses High Voltage mode DCDC, in default mode, ( no firmware ), the VDD should be 1.8V as default value in REGOUT0,
However the Voltage Level...
TWI Master drives BNO085 to read four-element data at intervals of 20ms, and I2C will not be able to read data when the device works for more than 10 minutes. INITTWI and...
I am trying to get the nRF Connect (Zephyr) fs_sample working with nRF5340 preview DK, but am getting the following errors: *** Booting nRF Connect SDK d96769faceca *** [00...
Hi,
Question is in Yellow
I am configuring the asset tracker v2 :
URL: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications/asset_tracker_v2...
I am using nRF Connect from inside of CodeVS IDE.
I am creating a new application by Copying a Sample. What sample should I use to communicate UART data between the nRF...
Hello I am working on a temporary workaround for the problem in this thread . The workaround is to reset the device using the Watchdog. However I can still see this problem...
I would like to test updating my Matter device based on the nRF5340 using the Matter OTA.
I am reading the documentation here:
https://project-chip.github.io/connectedhomeip...
When custom board with nrf52840 uses High Voltage mode DCDC, in default mode, ( no firmware ), the VDD should be 1.8V as default value in REGOUT0,
However the Voltage Level...
I am using a thingy53 and trying to get i2c devices to work via the qwiic/twic interface.
I bought: SparkFun Qwiic Buzzer - BOB-24474 - SparkFun Electronics and https:/...
How do I get the value of the characteristic of the service I created? I try to get it with the following code, but the content pointer returned is NULL.
TWI Master drives BNO085 to read four-element data at intervals of 20ms, and I2C will not be able to read data when the device works for more than 10 minutes. INITTWI and...
I am trying to get the nRF Connect (Zephyr) fs_sample working with nRF5340 preview DK, but am getting the following errors: *** Booting nRF Connect SDK d96769faceca *** [00...
I am attempting to work thru the tutorial exactly per the instructions, and I'm stuck in Lesson 1 at
6. Wait for the device to connect to nRF Cloud.
The Cellular Monitor...
Hello,
I'm currently working on using a MAX86141 sensor ( datasheet found here ), and I've been running into some issues with communicating with it since this is the first...
Hi,
I am using the nrf5340 to study the flow of BIS broadcast audio. I have two nrf5340s, one as gateway to run the broadcast_source program and one as headset to run the...
Hi all,
I'm a beginner of Nordic system, I use nRF52832(PCA10040) to develop my project, here is my properties:
Board: nRF52832 nRF5 SDK Version: 17.1.0 Soft device: S212...
Hi,
Question is in Yellow
I am configuring the asset tracker v2 :
URL: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications/asset_tracker_v2...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
Hello,
I have (2) Questions below highligted in yellow
I have followed these steps until Step 5 Substep (1-4)
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...