Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
RedBear Blend Micro use pairing passkey 0

Hi, I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device. Is it possible? Static passkey...
- ble blend passkey io
756 views

0 replies

Started over 10 years ago
by isi
Not Answered
How to interface multiple RF transmitters with single RF reciever? 0

How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ? I am working on a polling system. This one is similar to the audience...
- 433mhz
2341 views

0 replies

Started over 10 years ago
by Ajinkya
Not Answered
Writing peripheral characteristic value 0

Hello, I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
- value
- bluetooth low energy
- keil
- write
- nrf51822
- characteristic
2612 views

0 replies

Started over 10 years ago
by nejcokle
Not Answered

NRF24L01 Breakout boards 0

I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...

796 views

0 replies

Started over 10 years ago
by THLL
Not Answered

Nrf905 packets and CRC check methods 0

Hi, my friend, I've been with nrf905. I use a 16-bit CRC check. But I encountered problems in use: 1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...

991 views

0 replies

Started over 10 years ago
by Jesen

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018