Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF54LM20A-PAAA - VBUS consumption 0

Hello, I have not found any information about the VBUS current consumption. Is this information available? Do you know how much current flows through the VBUS pin? Thank...
- development
- nRF54LM20A
- usb
- hardware
5 views

0 replies

Started 8 minutes ago
by HW72
Not Answered
nRF54L15-Tag minimum sleep current 0

I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
61 views

0 replies

Started 13 hours ago
by John0123456
Not Answered
Tips for improving battery life on thingy:91X asset tracker template in no cell conditions 0

We are currently evaluating the nrf9151 via the thingy91X for our application we need the device to function in areas with no cell coverage and not drain the battery....
42 views

0 replies

Started 23 hours ago
by JackFitton
Not Answered
nrf5340: nRF Connect SDK Intermediate, Lesson 9, Exercise 5 (l9_e5_nrf5340_both_sol): with TFM, bootloops 0

Hi SDK: ncs-v3.4.2 I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM. I don't have the nrf5340dk but one with the same chip...
- development
- software
- zephyr
- nRF5340
85 views

0 replies

Started 2 days ago
by John-Eric Kamps
Not Answered
AT command to trigger MO ping 0

We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
52 views

0 replies

Started 2 days ago
by John Pedersen

Recent in the DevZone Blog

Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015