Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nrfconnect sdk partial erase will cause USAGE_FAULT on k_sleep() 0

Hi, i'm using nRF52832 to construct an BTHomev2 sensor. In development, we find the firmware seems to randomly fail in k_sleep(), but once we full earse the chip before...
17 views

0 replies

Started 6 hours ago
by AlanCui4080
Not Answered
Problem with function modem_info_params_get() in TN/NTN usecase 0

Hello, I am getting an error with the modem_info_params_get() function when I try to get the modem parameters. I am currently using SDK 3.2.0 with the FW MFW_nRF9151-NTN_v1...
16 views

0 replies

Started 15 hours ago
by GoncaloS
Not Answered
nRF52840 PWM: Continuous 1MHz clock with synchronized 126-bit data bursts using NRF_PWM_LOAD_INDIVIDUAL 0

I am working on an nRF52840 where I need the following outputs: a continuous 1MHz master clock a 126 bit serial bit data output sent out whenever a user wants with a...
23 views

0 replies

Started 15 hours ago
by Tim L
Not Answered
Pass custom instruction via nrfutil device qspi erase 0

Hello, I have a question regarding external flash erase via `nrfutil` command line tool. Does the `nrfutil device` command support doing a qspi erase with custom qspi commands...
20 views

0 replies

Started 15 hours ago
by avalancheverdant
Not Answered
Feature Request: Add KMU Provisioning to nRF Connect for Desktop Programmer tool 0

It would be nice to be able to provision the KMU of nRF54l15 devices directly from the nRF Connect Programmer Tool. This is currently only possible using the nrfutil command...
18 views

0 replies

Started 16 hours ago
by Rocky

Recent in the DevZone Blog

Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018