Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
In the smp_svr project, OTA fails after explicitly setting CONFIG_BT_SMP=y. 0

SDK v3.2.0 SMP Service: INITIALZING Always show " INITIALZING ".
7 views

0 replies

Started 4 hours ago
by Leo Mo
Not Answered
NRF54L05 how to surpport CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC in bare-metal SDK 0

Hi , NRF54L05 how to surpport CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC in bare-metal SDK,and while enable mcuboot OTA DFU feature ,how to modify the configuration?Thanks.
11 views

0 replies

Started 5 hours ago
by OPQ
Not Answered
nrf52833 scan extend adv packet 0

I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets， This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
6 views

0 replies

Started 5 hours ago
by xinzhenXU
Not Answered
UART, I2C, SPI, PDM and USB Pin Mapping for nRF5340 (NRF5340-QKAA-R7) 0

Hello Nordic Team, We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces . We have...
20 views

0 replies

Started 8 hours ago
by Mohammed Hashir P
Not Answered
Linux USB ports 0

I have a nrf9160dk that drives a screen via SPI, using an IT8951 controller. The firmware driving the screen works fine if I plug the USB cable on a power bank or using MS...
13 views

0 replies

Started 22 hours ago
by amelio

Recent in the DevZone Blog

Comparing compilers/IDEs for development with nRF5x series devices

Michael Dietz

#Introduction All compilers ARE NOT created equal. Given the same c code, different compilers will generate machine code with varying performance & size. Generally the more efficient machine code (uses…
- 28 Jan 2016
nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016