Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Request for RF Tuning Support – nRF54LM20 with nRF21540 FEM 0

Hi, We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM. We have already consulted with you regarding the design under Case ID...
10 views

0 replies

Started 39 minutes ago
by Irfan Memon
Not Answered
Achieving pin retention in nRF54L15 GPIO without hardware pull-up through sys_reboot() 0

Hi, I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for! My device has a power enable pin (on GPIO1) that must ideally...
68 views

0 replies

Started 22 hours ago
by htownclyde
Not Answered
l0destar - ultra low-power open-source hardware and software vehicle tracker you can build at home 0

Hi This isn't about a problem so I'm not sure if this is an inappropriate post to make here, if so please feel free to remove it, however there is no commercial incentive...
68 views

0 replies

Started 1 day ago
by m4rkw
Not Answered
NRF_MODEM_LIB_MEM_DIAG_ALLOC Kconfig setting needs log but increments the failed allocs (which is not only used for logging statistics but for diagnosis as well). 0

I am using the SDK v3.4.0 LTS for modem error debugging I included: prj.conf I am mapping errors depending on wether memory allocations failed. I am fetching the stats...
67 views

0 replies

Started 1 day ago
by Peter Horauer
Not Answered
An aborted Channel Sounding procedure leaves ~1 mA residual current until reset (SDC 200.12506) 0

If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
99 views

0 replies

Started 1 day ago
by Nat E

Recent in the DevZone Blog

Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015
Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015
How to use the latest Keil 5 for Keil 4 projects (.uvproj)

Stefan Birnir Sverrisson

As many have noticed, Keil 5 does not have native support for Keil 4 projects (project files ending with uvproj), it only has native support for Keil 5 projects (project files ending with uvprojx). However…
- 26 Mar 2015