Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to Configure Device Type via Serial for Matter over Thread Modules? 0

Hello Nordic community, I am currently working on developing applications for Matter over Thread and have set up my ZAP file accordingly. I've successfully flashed two types...
13 views

0 replies

Started 32 minutes ago
by OllLlllO
Not Answered
Does nrf54L15 support PA? 0

Hi， I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully. sdk: ncs2.8.0 project: direct_test_mode...
11 views

0 replies

Started 46 minutes ago
by Август
Not Answered
nRF5340 Build Issue 0

I am developing with the nRF5340, but I am encountering an issue where CONFIG_BOOTLOADER_MCUBOOT is not being enabled. Although I have enabled it in the prj.config file as...
9 views

0 replies

Started 1 hour ago
by giun.kim
Not Answered
Antenna for Small USB Receiver 0

Hi, We are designing a USB Receiver based off the Nordic Proprietary Radio + ESB. Do you have any reference designs for a PCB antenna which must be as small as possible...
7 views

0 replies

Started 1 hour ago
by AGeegee
Not Answered
Matter door lock using Bluetooth LE with Nordic UART Service 0

I am try to make Bluetooth LE with Nordic UART Service bondable in to pair with central, not requiring to enter pairing code again and again. I have set followings in prj...
18 views

0 replies

Started 6 hours ago
by BilalAliAhmad

Recent in Nordic blog

Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014

Latest guides

Getting Started : Getting started with Bluetooth Electronic Shelf Labels (ESL) and Periodic Advertising with Responses (PAwR)

Lorenzo Amicucci

The new Bluetooth 5.4 features Periodic Advertising with Responses (PAwR) and Encrypted Advertising Data (EAD) can be used for one-to-many applications. One of these is the Electronic Shelf Labels (ESL…
- 7 Aug 2024
nRF5x: General PCB design guidelines for nRF52 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Nov 2023
Software: Periodic Advertising with Responses (PAwR): A practical guide

Hung Bui

Periodic Advertising with Responses (PAWR) is a new feature in Bluetooth 5.4. It extends the periodic advertising protocol from Bluetooth 5.0. Periodic advertising, where a device sends broadcast data with…
- 13 Sep 2023
nRF5x: General PCB design guidelines for nRF53 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Jul 2023
Software and Protocols: nRF Cloud Access Provisioning

Charlie

Please note that some information on this page may be outdated due to ongoing improvements in nRF Cloud. For the most current details on provisioning services, refer to the nRF Cloud Security Services…
- 1 Dec 2022
Software and Protocols: Field verification of GNSS on the nRF91 Series

JaniM

Introduction The intention of this guide is to clarify and describe the main aspects relevant to the GNSS receiver functionality on the nRF9160 as well as build configurations, tool recommendations and…
- 10 Jun 2022