Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
PPK2 calibration offsets corrupted in EEPROM 0

Hello, My PPK2 (PCA63100, rev 1.1.2, build code 2026.8) reports corrupted calibration offsets: O0 / O2 ≈ 4.06e31, O3 ≈ −2.8e15, O1 / O4 ≈ 0, and the Power Profiler app shows...
1 view

0 replies

Started 4 minutes ago
by MarcoR
Not Answered
fs_mgmt file-upload write ACKed at link layer but never reaches Zephyr host (bt_recv_unsafe) on nRF54LM20A — related to IOS-nRF-Connect-Device-Manager#659 0

This is long and AI generated. Sorry about that, but it is comprehensive. I'm seeing a very specific, repeatable failure uploading a file via mcumgr's fs_mgmt over BLE,...
15 views

0 replies

Started 1 hour ago
by lcj
Not Answered
SoftDevice Controller / MPSL BabbleSim libraries for NCS v2.9.0 0

Hello, We run our Bluetooth Mesh product firmware in BabbleSim, on a simulated nRF52840 (nrf_hw_models, native simulator). We are on nRF Connect SDK v2.9.0. We would like...
19 views

0 replies

Started 1 hour ago
by Denis_Linkio
Not Answered
nRF54L05 wake on I2C standby current 0

An external MCU occasionally sends data to the nRF54L05 over I2C. Between transfers, the nRF54L05 should sleep and wake when addressed, without a separate wake pin. What...
58 views

0 replies

Started 19 hours ago
by Jonsiann
Not Answered
Thingy:53 Zigbee End Device — Configure Reporting failures + malformed Report Attributes flood 0

On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
- development
- software
- debugging
- zigbee
- zephyr
- nRF5340
54 views

0 replies

Started 20 hours ago
by Gabor Bohm

Recent in the DevZone Blog

Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018