Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Firmware developer needed for nRF52832 with DFU 0

I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
- software
- Lighting
- nrf5 sdk
- dfu
- Pre-production
- ios
852 views

0 replies

Started over 8 years ago
by jamie_wojcik
Not Answered
firmware update on PCA10040 kills debugging 0

I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
888 views

0 replies

Started over 8 years ago
by Karl
Not Answered
Any SoftDevice or Application (for nRF52840 PDK) to verify BT 5.0 Extended Advertising, Periodic Advertising, LE Long Range (2M PHY) and LE High Speed(2M PHY) ?? 0

Hi, I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
955 views

0 replies

Started over 8 years ago
by Anupam Roy
Not Answered
Android driver for USB nRF24LU1+ Crazyradio PA 0

I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
- nrf24
- android
- hardware
- Pre-production
1231 views

0 replies

Started over 8 years ago
by henry_329048
Not Answered
peer disconnect is not recognized when (connected peers < max peer number) in multiperipheral mode 0

Hi, I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
- nrf52832
964 views

0 replies

Started over 8 years ago
by kvskt

Recent in the DevZone Blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015
nRF51 Qt GCC Example

Jacob Portukalian

Hi Everyone! At Sky Wave Design, we recently switched all of our Nordic development over to using GCC and using Qt Creator as the IDE. We have released our example project on github for those of you…
- 31 Jul 2015