Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Accessing the USB data lines from the nPM1300EK 0

Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
- development
- usb
- hardware
- nPM1300
17 views

0 replies

Started 2 hours ago
by Scigrapher
Not Answered
nRF9151 DECT NR+ – PT association fails with MAC_STATUS_NO_RESOURCES (7) using official dect_shell sample 0

Hello, I am currently testing DECT NR+ communication between multiple nRF9151 SMA DK boards, but I am unable to establish a connection between an FT and a PT. I initially...
14 views

0 replies

Started 2 hours ago
by Damntrak06
Not Answered
nRF93M1: Test firmware updates 0

The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
17 views

0 replies

Started 4 hours ago
by JordanYates
Not Answered
nRF52840 HCI USB / SDC – How to configure per-connection event length and scheduling 0

Hi Nordic team, I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host. My application has multiple BLE connections...
60 views

0 replies

Started 15 hours ago
by Dzmitry
Not Answered
Community Project: Using PPK2 for Thermodynamic Computing on ARM Cortex; BOOP A Thermodynamic Voxel Architecture for Energy-Constrained Edge Computing 0

Hello DevZone Community, I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
54 views

0 replies

Started 16 hours ago
by Sam01234567

Recent in the DevZone Blog

Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015