Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
preempt 0

for a new ble device is better to use zephyr-rtos an old stile library ?
0 views

0 replies

Started a few seconds ago
by novello
Not Answered
High current consumption (~20 mA) during button press on nRF54L15 DK (Matter Contact Sensor sample) 0

Hello Support Team, I am currently working with the Matter contact sensor sample ( ncs\v3.4.0\nrf\samples\matter\contact_sensor ) on the nRF54L15 Development Kit (DK). ...
10 views

0 replies

Started 21 minutes ago
by IOANNIS0
Not Answered
Thingy:91 X PCA20065 - QM13345 LUT and MIPI RFFE manufacturer ID 0

Hi, I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design and I have two questions about the QM13345 configuration. 1. LUT The Thingy...
17 views

0 replies

Started 1 hour ago
by Jeff3813
Not Answered
SDC/central_esl (PAwR Advertiser): controller stops transmitting any radio traffic while HCI shell stays fully responsive — no assert, no disconnect event, no recovery 0

## Summary Our AP (unmodified upstream `central_esl` sample, running as PAwR **Advertiser** role, i.e. `CONFIG_BT_CTLR_SDC_PAWR_ADV`) periodically stops transmitting *any...
35 views

0 replies

Started 6 hours ago
by kingdomlin
Not Answered
SPI on "low drive, low frequency I/O" pins (P0.26–P0.29) — real max bit rate and RF impact on nRF52832? 0

I am designing a board around the nRF52832 (QFN48). According to Table 5 in the product spec, GPIOs P0.22–P0.31 are marked "Low drive, low frequency I/O only" (see §4.3.1...
34 views

0 replies

Started 6 hours ago
by hello0

Recent in the DevZone Blog

SwiftDuino

Jason

Uses Swift Language to run your Arduino project in your App via bluetooth. https://www.facebook.com/ucxpresso.nrf/posts/1193211740761762
- 15 Dec 2016
Fast Production Screening based upon Bluetooth DTM

Ken L

The challenge As a product is getting into the production phase, the need of a fast and standalone screening facility on the production line arises. Here I'm introducing a production screening setup…
- 9 Dec 2016
I am developing an open source sensor beacon board

zelin

I am developing an open source sensor beacon board named: YS-Beacon which contains: nRF52832 DAPLink - LPC11U35 9-Axis Motion Sensor Ambient Light Sensor、Proximity Sensor and 3D-Gesture Sensor with…
- 2 Dec 2016
nRF52 Rocket: Part I – Introduction to Model Rocketry and its UX Problem

Tony Wu

Official Launch Video Welcome to this 2 or 3-part blog about the nRF52 Rocket, a BLE-enabled model rocket, which you’ve just seen soaring through the air in the video above. In the first part of blog…
- 21 Nov 2016
What to keep in mind when developing your BLE Android app

Hung Bui

BLE is native supported on Android from v4.3. It has been continuously improved as Android evolving. It's getting more and more complex with additional features. It's important that a Bluetooth app should…
- 14 Nov 2016
Get started on PC Software for Mesh and Mesh DFU

David Edwin

nRF-connect-Mesh PC tool allows the user to demonstrate the nRF OpenMesh and the Mesh Device Firmware Update (DFU). The Mesh DFU will be used for nRF OpenMesh and the Bluetooth Mesh when it is made available…
- 11 Nov 2016