Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nrf_desktop: select peer by specific id 0

Can you select peer by peer's id rather than cycling?
20 views

0 replies

Started 1 day ago
by shanty
Not Answered
devicetree in VS code 0

Hi I would like to use DeviceTree in VS code. The VS code had installed "nRF Connect for VS Code Extension Pack" and tools chain. But I can't see any file in "DEVICETREE...
37 views

0 replies

Started 1 day ago
by LC2047
Not Answered
nRF9160 UART: UART_ASYNC_API Rx block while reading large data 0

Hi, everyone. I am testing reading/writing data between n52840 and n9160 through UART with buf_len=1(byte by byte) based on Zephyr's UART_ASYNC_API provided in ncs v2.6...
36 views

0 replies

Started 2 days ago
by siqi
Not Answered
Carrier Frequency offset calibration 0

Almost all of our carrier frequencies have the offset of 118KHz. How can I tune it in the software beside changing the capacitor? I have gone through and
40 views

0 replies

Started 2 days ago
by LongQi
Not Answered
Broadcast to Zigbee Messaging Cluster 0

Hello. Using the Zigbee messaging cluster, we are writing code for data exchange between ZR and ZED. (Based on the Zigbee example light_bulb/light_switch/light_coordinator...
30 views

0 replies

Started 2 days ago
by kim_mj

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017

Latest guides

Getting Started : Getting started with Bluetooth Electronic Shelf Labels (ESL) and Periodic Advertising with Responses (PAwR)

Lorenzo Amicucci

The new Bluetooth 5.4 features Periodic Advertising with Responses (PAwR) and Encrypted Advertising Data (EAD) can be used for one-to-many applications. One of these is the Electronic Shelf Labels (ESL…
- 7 Aug 2024
nRF5x: General PCB design guidelines for nRF52 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Nov 2023
Software: Periodic Advertising with Responses (PAwR): A practical guide

Hung Bui

Periodic Advertising with Responses (PAWR) is a new feature in Bluetooth 5.4. It extends the periodic advertising protocol from Bluetooth 5.0. Periodic advertising, where a device sends broadcast data with…
- 13 Sep 2023
nRF5x: General PCB design guidelines for nRF53 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Jul 2023
Software and Protocols: nRF Cloud Access Provisioning

Charlie

Please note that some information on this page may be outdated due to ongoing improvements in nRF Cloud. For the most current details on provisioning services, refer to the nRF Cloud Security Services…
- 1 Dec 2022
Software and Protocols: Field verification of GNSS on the nRF91 Series

JaniM

Introduction The intention of this guide is to clarify and describe the main aspects relevant to the GNSS receiver functionality on the nRF9160 as well as build configurations, tool recommendations and…
- 10 Jun 2022