Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Cannot program my NRF5340 DK after some time. "Failed to write DebugPort register 2: Unknown Error in J-Link DLL" 0

After some time I picked up my NRF5340 DK again to continue my Matter samples. But I noticed I cannot program any sample to it. The Segger seems to work fine, as I'm able...
11 views

0 replies

Started 1 hour ago
by lukas.kirner
Not Answered
error: 'DT_N_S_soc_S_spi_40004000_S_sst26vf032b_0' undeclared (first use in this function); did you mean 'DT_N_S_soc_S_spi_40004000_S_sst26vf032b_0_BUS'? 0

Im a bit stuck here. I have the following code, trying to communicate with a flash memory: Overlay: code: I get the following error message: error: ...
12 views

0 replies

Started 2 hours ago
by Boggibill
Not Answered
Wi-Fi Positioning with DECT NR+ modem firmware 0

I have a nrf9151dk with a nrf7002ek shield. The nrf9151dk has the DECT NR+ PHY firmware running on the modem core. I would like to do Wi-Fi positioning with the nrf9151dk...
13 views

0 replies

Started 3 hours ago
by yali
Not Answered
Periodic advertising data 0

Hi, I am trying to understand periodic advertising and some basic questions: I am using periodic_adv example from the NCS. I see teo ADV data defined in the file as...
18 views

0 replies

Started 5 hours ago
by DanisXZ
Not Answered
how to enable pm managment at nrf5340 0

software:ncs 2.5.0 hardware:nrf5340 dk hi professor, According to the article at https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf53...
19 views

0 replies

Started 6 hours ago
by sunnyyang

Recent in Nordic blog

Start Up Extreme Norway

John Leonard

Last week I attended what was my first Startup event, but after experiencing the energy there, I can safely say it will not be my last. 3 days of seminars, networking and lots of fun kicked off in Bergen…
- 22 Jun 2015
Step by Step Guide to Setup and Start Developing with the nRF51 DK and Keil

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, get the tools installed and get the software (SW) development environment…
- 17 Jun 2015
Debugging using QtCreator on Mac

wim

This post started as a question, but got the suggestion to post this as a blog post. Here it is. I have been trying to get QtCreator configured such that I can use it as my IDE for the nrf51822 on Mac…
- 12 Jun 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019