Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to confirm image installed by MCU boot 0

Hi, I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
0 views

0 replies

Started a few seconds ago
by Torsten Robitzki
Not Answered
nRF5340 Audio DK as both LE audio and BLE transfers 0

Hi, We are currently working with the nRF5340 Audio DK board and aim to implement Bluetooth Low Energy (BLE) message transmission alongside the existing LE audio transmission...
24 views

0 replies

Started 1 hour ago
by Virat
Not Answered
Configuring RTC with Zephyr device tree approach 0

I need to develop the code for RTC configuration without using nrf_drv_rtc_* , hence I started using zephyr device tree approach . Below is my code . #include <stdio.h...
20 views

0 replies

Started 1 hour ago
by PavanKumar_cr
Not Answered
Measure solar panel current 3 W 5 Volt 0

HI, I have two solar panes for my project 3W 5V and 2 W 9V. I would to measure current of the panels with the Power Profiler II. I think this should work (my calc is 3W...
19 views

0 replies

Started 2 hours ago
by pede
Not Answered
Can we use nrd52840dk as bluetooth(for data transmission) and to calculate distance using multi carrier phase difference method between itself and nrf52840 dongle 0

Hi Can we use nrd52840dk as bluetooth(for data transmission to user created mobile app) and to calculate distance using multi carrier phase difference method between itself...
19 views

0 replies

Started 6 hours ago
by VishnuG

Recent in Nordic blog

On nRF Connect for Mobile 2.5, and performance as the root of all... benefit?

Dinesh Harjani

Tell me if this has happened to you before. You open some file, one you haven't touched in a while. This might be because you need to use an API, a coworker of yours wrote. Maybe it's a library or package…
- 20 Apr 2022
micro:bit v2 Pager

Ali Aljaani

In this blog post, we will show you how to build a pager with a micro:bit v2 and nRF Connect SDK. Writing application in C using nRF Connect SDK gives you the highest level of control over the micro:bit…
- 8 Apr 2022
Comparing range with Bluetooth Low Energy of the nRF21540 DK and the nRF52840 DK

Susheel Nuguru

FYI: The video above shows a similar test as this blog post, just using two nRF52840 DKs and two nRF21540 DKs. The blog post uses one nRF52840 DK and two nRF21540 DKs. One of the reasons we did multiple…
- 7 Apr 2022

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019