Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
BLE AD CAN'T BE CONNECTED ON NRF52810 THAT ENABLE BLE AND ANT+ ON S312 0

I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
- development
- software
- nrf52810
- s312
- bluetooth le
4 views

0 replies

Started 2 minutes ago
by zhangchenfang
Not Answered
error -22 when subscribing to HOGP reports 0

I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
- development
- software
- C
- bluetooth le
- nrf52840
6 views

0 replies

Started 13 minutes ago
by Orlin
Not Answered
pulse counting with GPIOTE, PPI and TIMER 0

Hello, I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
11 views

0 replies

Started 31 minutes ago
by Pepam
Not Answered
SPIM3 draws higher current even with Errata workaround 0

Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
13 views

0 replies

Started 1 hour ago
by Ankit_chauhan
Not Answered
GAZELL and BLE simultaneously activated not working 0

Hello Nordic Team I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
14 views

0 replies

Started 1 hour ago
by Christophe_

Recent in Nordic blog

Writing BLE firmware with a few lines of code part 2

Nguyen Hoan Hoang

Second part of the series Writing Bluetooth LE firmware the easy way blog. This second part shows how to read and advertise the environment sensor data (BME280 using Motsai Neblina module and BME680 using…
- 3 Jan 2018
Intro to ShockBurst/Enhanced ShockBurst

Daniel Veilleux

The first generation of wireless PC accessories to achieve widespread success (the ones that shipped with a dongle in the box) adopted 2.4GHz radios because these radios offered the optimal trade-off between…
- 1 Jan 2018
Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017