Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
UART configuration in a runtime 0

Hello, My board contains nRF9160 and two nRF52840. One of nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with each nRF52840 over separate...
- development
- nRF9160
- configuration
- C
- zephyr
- nrf52840
- dfu
2 views

0 replies

Started 5 minutes ago
by tdfilip
Not Answered
how to over write data in same offset into internal flash on zephyr 0

Hi, I am using the nRF Connect SDK 2.6.1 with the nRF5340 board. I referred to the soc_flash_nrf example to read and write data into flash. I need to overwrite data...
13 views

0 replies

Started 1 hour ago
by ChiragBhavsar
Not Answered
Wireshark : Encrypted packet decrypted incorrectly (bad MIC) and Empty PDU 0

Hi, I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone. I can capture all the pairing process, I see DHKey exchange...
15 views

0 replies

Started 1 hour ago
by MalloryLP
Not Answered
Partition map migratation from ncs 2.2 -> ncs 2.7 (sysbuild) 0

Hi, I have a firmware running on ncs 2.2 with mcuboot and tfm which I'm in the process of upgrading to ncs 2.7 with sysbuild. I currently have a problem converting the...
22 views

0 replies

Started 2 hours ago
by Christoffer Brask
Not Answered
nrf52840 dk to upload code to nrf52811 0

Hi This is my first project to make my custom PCB. I have a question about how can I uploaded my code with segger embedded studio by using nrf52840 dk? For the hardware...
- development
- software
- softdevice
- nrf52840
- nRF52811
19 views

0 replies

Started 2 hours ago
by nordicDK

Recent in Nordic blog

On nRF Connect for iOS & SIMD Optimizations in Swift

Dinesh Harjani

We released a small update late last week. It’s a follow-up to our last release of 2019, and like its predecessor, this release, 2.1.2, aims to improve the general stability of nRF Connect for iOS as well…
- 31 Jan 2020
Q&A for "Embedded Antennas for IoT" webinar

Petter Myhre

This blog post contains answers to questions asked during the "Embedded Antennas for IoT" webinar hosted by Nordic Semiconductor 17.10.2019. You can watch a recording of the webinar here. You…
- 22 Nov 2019
nRF Connect 2.1 for iOS: Welcoming Dark Mode

Dinesh Harjani

It has taken a lot longer than we previously thought, but we made it here, to our first big point release for nRF Connect 2.0. Throughout this “two-point-oh" journey, you’ve been an invaluable asset to…
- 19 Nov 2019

Latest guides

Bluetooth low energy: Wireless timer synchronization among nRF5 devices

Audun

Introduction In a variety of use cases there is a need to share a common clock among multiple devices. Such a common clock can be used for many purposes, for example by having each node in a network perform…
- 12 Jul 2016
nRF5x: General PCB design guidelines for nRF52 series

FormerMember

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 11 Jul 2016
Software Development Kit: Migrating to Peer Manager

Øyvind Rønningstad

The tutorial has been updated for SDK v11, which contains the production-ready release of Peer Manager. The original tutorial can be found on this page, below the updated tutorial. #Migrating to Peer…
- 8 Apr 2016
Bluetooth low energy: Bluetooth low energy Characteristics, a beginner's tutorial

MartinBL

Before we begin Table of content Topics that will be covered include: Before we begin Basic theory Attribute tables in nRFConnect Bluetooth Low Energy application Description of the example Adding a…
- 18 Mar 2016
Bluetooth low energy: Bluetooth Smart and the Nordic's Softdevices - Part 2 Connection

Hung Bui

This blog series was created as an attempt to fill in the gap between how Bluetooth Smart is described in the spec and how you can use our APIs and event from our softdevice to do what defined in the spec…
- 1 Feb 2016
Design Examples: Capacitive Touch on the nRF52 series

Einar Thorsrud

Important updates: Due to erratum 84 (COMP: ISOURCE not functional), capacitive sensing using the relaxation oscillator method is not usable in a real product with the nRF52832, as it will only work reliably…
- 31 Jan 2016