Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
NRF52805 DTM setup reset command failed 0

I using nrf52805 for DTM, in sdk17.1, pca10040e. I only changed RXTX pin number, but did not modify the rest. Then use Nordic Connect for DTM testing, and the following prompt...
10 views

0 replies

Started 34 minutes ago
by zhangchenfang
Not Answered
DYNAMIC_INTERRUPTS Fail in "esb_ptx" Sample 0

HI, I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
10 views

0 replies

Started 38 minutes ago
by gandyhuang
Not Answered
Output pins configured in the Overlay, not showing in Devicetree view 0

I have the following setup in my overlay file: relay { compatible = "gpio-relay"; relay1: relay_1 { gpios = <&gpio0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; label = "DC Mtr...
16 views

0 replies

Started 1 hour ago
by MontanaEE
Not Answered
Move console, bt-mon, etc to RTT 0

I need to move everything off of UART0 so I can use it for my touchscreen On a previous post I was told I could move everything to RTT in the overlay, but when I try to...
16 views

0 replies

Started 1 hour ago
by MontanaEE
Not Answered
The relation for PIN reset and other reset 0

Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
15 views

0 replies

Started 1 hour ago
by FACE@shibuya

Recent in Nordic blog

Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018
Introducing experimental release of Programmer Application

Reidar Martin Svendsen

nRF Connect for desktop has proven its flexibility by being cross platform and ability to install and update applications based on users need. Motivation Our initial goal was to modernize and cover…
- 30 Apr 2018

Latest guides

nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019
Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019