Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
NRF52832's GPIO interrupt mis-triggering 0

I use the gpio8 interrupt to detect whether the SD card is inserted. When a falling edge is generated, it means that the SD card is inserted. But I found that sometimes, the...
13 views

0 replies

Started 1 hour ago
by shiyu
Not Answered
MDBT42Q BLE not working when porting code from nrf52 dk 0

I am trying to port code I developed on the NRF52 DK to a MDBT42Q-512KV2 BLE module from Raytac I purchased from Digikey and am running into problems. I developed all the...
20 views

0 replies

Started 1 hour ago
by Danie1
Not Answered
Why am I receiving data through /dev/ttyACM1 while transmitting over pin 8 (UART1 TX) on nRF9151? 0

Hi, I'm working with the nRF9151DK and Zephyr RTOS (v3.7.99 / NCS 2.9.1) . I’ve configured UART1 to send and receive data via GPIO pins: TX: pin 8 (P0.08) RX:...
- development
- nRF9151
- C
- zephyr
- hardware
17 views

0 replies

Started 6 hours ago
by jarain78
Not Answered
Extract Device name from Reflector in CS 0

Hi, I am struggling a bit on how to correctly extract the device name of the reflector, which is present in the Advertisement Data. The code that i have down below shows...
- development
- python
- software
- nRF Connect SDK
- nRF Tools
- nRF54L15
- bluetooth le
- nfc
18 views

0 replies

Started 7 hours ago
by NickDeLeenheer
Not Answered
RV8263-C8 I2C issues 0

Hello everyone, I have a custom board with an nRF5340, which currently uses the internal clock. I'm trying to use the RV8263-C8 RTC to achieve accurate real-time tracking...
15 views

0 replies

Started 7 hours ago
by Luis Santos

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started: nRF52840 Dongle Programming Tutorial

Einar Thorsrud

This tutorial demonstrates how to adapt and program SDK example applications to the nRF52840 dongle using USB DFU. It also describes how to program the dongle via Serial Wire Debug (SWD) using an external…
- 27 Nov 2018
Getting started: Announcing the nRF Connect for Cloud Device API Preview

Markus Tacker (he/him)

We are happy to announce our first release of the nRF Connect for Cloud Device API! Connect your BLE, LTE/NB-IoT or any other device to our free IoT development platform and interact with that device through…
- 12 Oct 2018
Bluetooth low energy: Merging two BLE examples together

Håvard

This is a follow-up to my previous blog post; adding custom commands to a BLE example. I hope it was interesting to see an example of adding the vendor specific Nordic UART service (NUS) into another…
- 6 Sep 2018
Software Development Kit: Getting started with Nordic's Secure DFU bootloader, a step by step guide

Hung Bui

The content of this blog was based on the documentation of BLE Secure DFU example, Bootloader module library and Buttonless DFU service from our SDK. Here we provide you step by step instructions to make it…
- 20 Mar 2017
Getting Started: Introduction to Bluetooth low energy and Bluetooth low energy development (video tutorial)

FormerMember

We have produced a video tutorial in two parts about Bluetooth low energy. The purpose is to give you a developer’s introduction to BLE and the development tools offered by Nordic Semiconductor. NB! Please…
- 6 Oct 2016
Bluetooth low energy: Wireless timer synchronization among nRF5 devices

Audun

Introduction In a variety of use cases there is a need to share a common clock among multiple devices. Such a common clock can be used for many purposes, for example by having each node in a network perform…
- 12 Jul 2016