Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Why am I receiving data through /dev/ttyACM1 while transmitting over pin 8 (UART1 TX) on nRF9151? 0

Hi, I'm working with the nRF9151DK and Zephyr RTOS (v3.7.99 / NCS 2.9.1) . I’ve configured UART1 to send and receive data via GPIO pins: TX: pin 8 (P0.08) RX:...
- development
- nRF9151
- C
- zephyr
- hardware
0 views

0 replies

Started 1 hour ago
by jarain78
Not Answered
Extract Device name from Reflector in CS 0

Hi, I am struggling a bit on how to correctly extract the device name of the reflector, which is present in the Advertisement Data. The code that i have down below shows...
- development
- python
- software
- nRF Connect SDK
- nRF Tools
- nRF54L15
- bluetooth le
- nfc
0 views

0 replies

Started 2 hours ago
by NickDeLeenheer
Not Answered
RV8263-C8 I2C issues 0

Hello everyone, I have a custom board with an nRF5340, which currently uses the internal clock. I'm trying to use the RV8263-C8 RTC to achieve accurate real-time tracking...
0 views

0 replies

Started 2 hours ago
by Luis Santos
Not Answered
Sample Android code for CTS gatt-server to use with nrfconnect CTS client 0

Hi, Looked into public Nordic repositories in github looking for a recommended implementation of CTS (current time service) to use with this sample: https://docs.nordicsemi...
0 views

0 replies

Started 7 hours ago
by Pedro Sousa
Not Answered
BLE Direct Test Mode, UART communication not working on nRF9160 DK / nRF52840 0

Hi, I have been experimenting with the Direct Test Mode program. I am using an nRF9160 DK, specifically the bluetooth chip nRF52840. The Direct Test Mode is not officially...
15 views

0 replies

Started 10 hours ago
by zachary_z

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020