Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Microphone options for nRF9061 DK 0

Is there any analog to digital input on the nRF9061 SiP / DK? I essentially need to plug in a microphone to this, so I looked at a couple of options -- ADC, the DMIC interface...
15 views

0 replies

Started 49 minutes ago
by nrao32
Not Answered
Capacitive sensing with nrf53 0

Hi, We want to implement capacitive sensing of nrf53. Can you help how I can use the nrf53 for capacitive sensing feature, as there is not much information given in datasheet...
13 views

0 replies

Started 1 hour ago
by Rahul Wagh
Not Answered
NRF52805 DTM setup reset command failed 0

I using nrf52805 for DTM, in sdk17.1, pca10040e. I only changed RXTX pin number, but did not modify the rest. Then use Nordic Connect for DTM testing, and the following prompt...
17 views

0 replies

Started 2 hours ago
by zhangchenfang
Not Answered
DYNAMIC_INTERRUPTS Fail in "esb_ptx" Sample 0

HI, I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
17 views

0 replies

Started 2 hours ago
by gandyhuang
Not Answered
Output pins configured in the Overlay, not showing in Devicetree view 0

I have the following setup in my overlay file: relay { compatible = "gpio-relay"; relay1: relay_1 { gpios = <&gpio0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; label = "DC Mtr...
21 views

0 replies

Started 3 hours ago
by MontanaEE

Recent in Nordic blog

The KEY POINT of example "ble_app_uart"

QQ645116977

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017
Introduce smart motion controller - ELIO

caram5555

"ELIO" is a Bluetooth module and smartphone application that can drive motor(DC, Servo) and illuminate LEDs. This module mounts Nordic's nRF52832 and motor controller IC. Smartphone application can create…
- 12 Dec 2017
Programming and debugging custom nRF5x devices

Anders Strand

Programming and debugging the nRF5x on our Developments kits is straight forward. Doing the same when you are using other boards might not be so easy. In this blog post we will explain which components…
- 8 Dec 2017

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020