Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Configuring UART1 from Scratch in Zephyr (Beginner Here) 0

Hey everyone! I’m working on a project using Zephyr with an nRF5340 board and trying to configure UART1 completely from scratch. Most tutorials I’ve found only cover UART0...
4 views

0 replies

Started 12 minutes ago
by Anassoumi
Not Answered
VSC: how to make a project fit for svn or indeed any version control 0

I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had absolute paths which filled me with dread as it means a...
20 views

0 replies

Started 1 hour ago
by DiBosco
Not Answered
llext on nRF52840DK 0

Hi Nordic team, I was testing whether Zephyr's LLEXT would work on the nRF52840DK. The example can be compiled on NCS 2.7.0 and loads fine. However the final step of having...
14 views

0 replies

Started 1 hour ago
by mabe
Not Answered
Voltage drop triggers BOR reset; MCU occasionally completely freezes 0

Hi, I'm facing a critical issue with our sensor's power setup and would really appreciate any insights or suggestions. Our sensor is currently using a CR2477 battery,...
14 views

0 replies

Started 1 hour ago
by Phobios
Not Answered
Add FOTA over BLE to nrf9151+nrf52840 0

Hi, I have a board which is nrf9151 with nrf52840 as BLE controller connected via hci_lpuart. This works fine so far, I am able to do simple AT commands as well as doing...
9 views

0 replies

Started 2 hours ago
by Michal

Recent in Nordic blog

Use Microbit to create a remote controlled car

Lars Sundell

The ultra simple to use pxt editor for Microbit (https://pxt.microbit.org/) supports sending data using the nRF51822 radio. The tool supports using both BLE and proprietary protocols. For this project…
- 27 Oct 2016
We developed tiny robots for swarm robotics research using nRF51422 (mROBerTO)!

Jay

mROBerTO (milli-ROBot-TOronto) is a small modular millirobot designed and implemented for swarm robotics research. It was first featured in the 2016 IEEE/RSJ International Conference on Intelligent Robots…
- 25 Oct 2016
Segger Embedded Studio - A Cross Platform IDE

Hung Bui

Download and Setup Download Embedded Studio >= v3.10e Download and install the J-Link Software and Documentation Pack >= v6.10g Download and unzip Nordic's nRF5 SDK >= v12.0.1 Note…
- 21 Oct 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019