Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SLM fault on startup with UART2 0

Hello, I'm working on a project that uses the Serial LTE Modem (SLM) application on a custom board. The main processor sends data to the nRF9160 over UART. The project is...
19 views

0 replies

Started 1 hour ago
by Mike12345
Not Answered
GRTC is not cleared on reset, causes Zephyr sys_clock to break when uptime > 20 hours 0

By default the GRTC peripheral is not cleared when started via sys_clock_driver_init . This is because nrfx_grtc_init calls nrfy_grtc_prepare , however NRFX_GRTC_CONFIG_CLEAR_AT_INIT...
24 views

0 replies

Started 2 hours ago
by Nick Ewalt
Not Answered
Flash to nRF5280 on Xiao Sense Plus with Development Kit 0

Hi I want to know if I can use the nRF52850-DK to flash the Xiao Sense Plus from seeed? I am following the following tutorial which says I need to use a J-Link but that's...
17 views

0 replies

Started 4 hours ago
by zach-nala
Not Answered
BLE Extended Advertisement BLE Dongle Support 0

Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
23 views

0 replies

Started 4 hours ago
by Shuhao Dong
Not Answered
Problem with BLE advertisement after migration to NCS v2.9.0 0

Hello, I had working BLE application build on v2.6.2. After migration to SDK v2.9.0 BLE is not advertising anymore. I think it may be related to default controller that is...
19 views

0 replies

Started 5 hours ago
by jkop_thaumatec

Recent in Nordic blog

NFC tag antenna tuning

FormerMember

NFC principle A NFC system consists of two devices, an active and a passive device. The active device is powered, and induces a magnetic field with a coil inductor antenna. When the passive device is placed…
- 20 Jun 2016
NRF52 debugging with QtCreator on Windows

Globuloz

Hello I succeeded to configure QtCreator toolchain to compile and debug my NRF52 board. So I wanted to share. I use my own Makefile to compile everything so I will focus here on how to run a debug session…
- 17 Jun 2016
BLE-Cube — A Bachelor Project

BLE Cube

In spring 2016 four students from NTNU got an assignment from Nordic Semiconductor. To compliment this assignment, the students wrote a short article: "What if controlling household appliances with your…
- 15 Jun 2016

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020