Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
FLPR GPIO Interrupts 0

Hello, I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
94 views

0 replies

Started 1 day ago
by Robert de Brum
Not Answered
Clarification on Mode 0 measured_freq_offset and frequency_compensation in Bluetooth Channel Soundinb 0

Hi Nordic team, I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively. I am using NCS 3.3...
49 views

0 replies

Started 1 day ago
by Rehan0
Not Answered
nrf54lm20a OTA fail 0

Hi: I use sdk ncs3.3.0 and nrf54lm20dk. Failed to return using AA dfu_target_init. OTA firmware is zephyr.signed.bin. I: DFU header I: 3d b8 f3 96 00 00 00 00...
73 views

0 replies

Started 1 day ago
by john.liu
Not Answered
v3.4.0 samples, specifically MCUboot+sysbuild+ns-variant+dts-style partitioning example 0

Hello, I've been asked to create a new ticket for this. It follows on from @ Erlend Isachsen asked: So before marking this problem as resolved, it would be nice to be...
82 views

0 replies

Started 2 days ago
by embeddedCoder
Not Answered
Speed up first connection to cell? 0

I am developing on the nrf9151 with SDK v3.4.0. The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
- development
- battery
- lte-m
- nb-iot
- nRF9151
- iot sdk
- configuration
52 views

0 replies

Started 2 days ago
by Peter Horauer

Recent in the DevZone Blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017
Bluetooth 5 2Mbps Demo with nRF52 Series and Samsung Galaxy S8

John Leonard

Bluetooth 5 - now arriving in smartphones As we know, Bluetooth 5 was launched last December by the Bluetooth SIG. The nRF52 Series from Nordic have always had Bluetooth 5 and its arrival in the mix for…
- 9 May 2017
Setting up Segger on a mac or pc and debug - step by step for humans

Lola

Most guides out there are unclear and made for machines. Here is a full guide how to setup Segger for mac OS X with some example project from the SDK ( or even a PC but not tested), and also how to debug…
- 5 May 2017
FreeRTOS threads preview with J-Link, GDB/Eclipse

Radoslaw Koppel

Short note how to make FreeRTOS program debugging with eclipse little simpler. If you are looking the information how to configure the whole environment see this post: https://devzone.nordicsemi.com/tutorials…
- 11 Apr 2017