Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF93M1: plans to expose LTE Timing Advance through the AT command interface? 0

Hello Nordic Support, I am developing a cellular positioning solution using an nRF93M1 LTE Cat 1 bis module. I currently use the following command to retrieve the serving...
22 views

0 replies

Started 1 hour ago
by ing-barbiz
Not Answered
Request for RF Tuning Support – nRF54LM20 with nRF21540 FEM 0

Hi, We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM. We have already consulted with you regarding the design under Case ID...
65 views

0 replies

Started 1 day ago
by Irfan Memon
Not Answered
Achieving pin retention in nRF54L15 GPIO without hardware pull-up through sys_reboot() 0

Hi, I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for! My device has a power enable pin (on GPIO1) that must ideally...
103 views

0 replies

Started 2 days ago
by htownclyde
Not Answered
NRF_MODEM_LIB_MEM_DIAG_ALLOC Kconfig setting needs log but increments the failed allocs (which is not only used for logging statistics but for diagnosis as well). 0

I am using the SDK v3.4.0 LTS for modem error debugging I included: prj.conf I am mapping errors depending on wether memory allocations failed. I am fetching the stats...
86 views

0 replies

Started 2 days ago
by Peter Horauer
Not Answered
An aborted Channel Sounding procedure leaves ~1 mA residual current until reset (SDC 200.12506) 0

If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
111 views

0 replies

Started 3 days ago
by Nat E

Recent in the DevZone Blog

How to setup the Thread demo displayed live at Google I/O

Petter Myhre

Google I/O was wrapped up last week. One session was particularly interesting: "Connect Thread Devices to the Cloud with IoT Core". In it Google explains how the Thread protocol and their Cloud IoT Core…
- 15 May 2019
Field-testing how distance affects the behavior of LTE-M and NB-IoT

Petter Myhre

There is an updated field test at the same location from 2022. During the updated field test, we captured more parameters for both LTE-M and NB-IoT devices and, we captured power measurements of the cellular…
- 2 May 2019
SEGGER Embedded Studio Nordic edition updates v4.16

Hung Bui

Recently, we've updated the SEGGER Embedded Studio Nordic edition (SES) to version 4.16 (SES Nordic Edition is special version of SES built specifically for nRF Connect SDK). This updated version introduced…
- 12 Apr 2019
nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018
Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018