Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
UART Hardware Flow Control 0

Hello Nordic community, using nrf5-sdk for nrf52840 SoC, I followed the uart example as below. The uart tx and rx works fine BUT NOT THE HWFC eg. When the CTS is set...
54 views

0 replies

Started 22 hours ago
by maveli
Not Answered
What are the features, performance, and usage limitations of the built-in GNSS and 4G in the nRF9151 NTN module? 0

Hello, We are currently designing an NTN satellite IoT terminal product based on the nRF9151 NTN module, primarily for tracker-type applications. In addition to NTN satellite...
- Evaluation
- nRF9151
- NTN eval
- hardware
92 views

0 replies

Started 1 day ago
by Baoxiang
Not Answered
Clarification on nRF21540 FEM TX Gain Selection (CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB vs MODE Pin / POUTA & POUTB) 0

Hi Nordic Team, Below are the configurations that I have done for the nRF21540 FEM. .config file # # Multiprotocol service layer (MPSL) # # CONFIG_MPSL_FEM_ONLY is not...
60 views

0 replies

Started 1 day ago
by Uma Maheshwar Reddy
Not Answered
nPM1300 EK charge‑discharge profile logging abnormal at 45 °C 0

Excuse me. When the customer uses the nPM1300 EK for battery charge‑discharge profile logging, after charging completes at 45 °C and the USB cable is unplugged as prompted...
97 views

0 replies

Started 2 days ago
by Mason Bu
Not Answered
PWM in nRF54L15 with power management 0

Sorry, this post is deleted.
764 views

0 replies

Started 9 months ago
by Gujju

Recent in the DevZone Blog

nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016