Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Update firmware with DFU bootloader but only use a prefix for bootloader settings 0

I'd like to update a firmware which is essentially made of 2 parts, say 0x1000-0x8000 is a "read-only" part and 0x8000-0x50000 is a "read-write" part. If I flash this firmware...
- development
- software
- nrf52840
- dfu
4 views

0 replies

Started 6 minutes ago
by ia0
Not Answered
CONFIG_USB_CDC_ACM was assigned the value y, but got the value n. Missing dependencies: DT_HAS_ZEPHYR_CDC_ACM_UART_ENABLED 0

Hello, As the subject says, I am working on a project that when I try to enable the CONFIG_USB_CDC_ACM in my prj.conf I see this error post-build. It seems to not matter...
7 views

0 replies

Started 15 minutes ago
by iRowBoats8
Not Answered
NRF54L15DK Development Board Not Connecting to PC (Windows 11) 0

Description: I encountered an issue where my NRF54L15DK development board fails to connect to my Windows 11 PC. Upon plugging in the board, the LED near the debugger starts...
15 views

0 replies

Started 36 minutes ago
by Ben Wisdom
Not Answered
Hardware connection to SIM880L module? 0

I'm trying to connect a SIM800L to my nrf52840-dk which I power through 5V USB. I'm a beginner at electronics so just want to make sure I understand how to wire things, please...
14 views

0 replies

Started 36 minutes ago
by olalonde
Not Answered
What are the prerequisites to get the ICCID 0

Hi, I would like to know what are the prerequisites to get the ICCID of the sim card: This is the code I use, nothing special. I can get the IMEI of the modem but not...
11 views

0 replies

Started 56 minutes ago
by lseg

Recent in Nordic blog

Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015
Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019