Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
The finer points of PWM on nRF52 using two chained buffers 0

I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
- pwm
- nRF52833
- hardware
- Pre-production
15 views

0 replies

Started 1 hour ago
by kevinjwalters
Not Answered
Subject: Cannot use GPIO P0.19 on nRF9160 as UART TX pin 0

Hi everyone, I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree: uart1_default...
23 views

0 replies

Started 3 hours ago
by thwcs7
Not Answered
Do o need ble bootloader separately 0

I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
17 views

0 replies

Started 3 hours ago
by Subham
Not Answered
Find My Get Serial Number Self certification test case failing 0

Hello, I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
21 views

0 replies

Started 4 hours ago
by maelclerambault
Not Answered
I2C devices are not getting detected in NRF54L15 Dev Kit. 0

I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
- software
- beginner
- nRF Connect SDK
- debugging
- nRF54L05
- Evaluation
- Protocol
- nRF54L15
- documentation
- zephyr
- twi
19 views

0 replies

Started 4 hours ago
by rsramki

Recent in Nordic blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018
Introducing experimental release of Programmer Application

Reidar Martin Svendsen

nRF Connect for desktop has proven its flexibility by being cross platform and ability to install and update applications based on users need. Motivation Our initial goal was to modernize and cover…
- 30 Apr 2018
New in nRF5 SDK v15: Strong Hardware-Based Security with Infineon OPTIGA Trust X

ChristianLesjak

Defining a business model and implementing a technical infrastructure are two major phases in building a successful product or IoT system. However, protecting the business model and your customer’s data…
- 9 Apr 2018