Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5340 BLE Audio Request for Schematic Review 0

I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
- Evaluation
- nPM1100
- bluetooth le
- low-power
- rf design
- hardware
- nRF5340
48 views

0 replies

Started 7 hours ago
by DavidMorina103
Not Answered
b0 fails to boot using swap algorithm in SDK 3.2.1 in nrf5340 0

Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
34 views

0 replies

Started 7 hours ago
by AlejandroM
Not Answered
BLE disconnect reasone 8 0

Hi everyone, I'm using the nRF5340 on a custom PCB board without an external 32 kHz oscillator. On the network core I flashed the hci_ipc sample. For some reason I occasionally...
42 views

0 replies

Started 9 hours ago
by Petar02
Not Answered
DECT NR+ rssi-1 measurement results saturated 0

Hello, I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware. The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
29 views

0 replies

Started 9 hours ago
by dame
Not Answered
DPPI and GPIOTE BLE events on nRF54L15 0

Hi all, I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
54 views

0 replies

Started 11 hours ago
by ArneVds

Recent in the DevZone Blog

Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018
The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018