Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
PCA10040 dk flash entire erase after linked to jlink 0

I'm developing with PCA10040 DK(3.0.0 2022.10), the IDE is SES for ARM 5.42a. The app is normal after download the application. After a reset or power off and restart, the...
18 views

0 replies

Started 1 hour ago
by lzq597
Not Answered
nRF52840 Oscillator not working 0

Hi, We have designed a custom nRF52840 development board based on the XIAO nRF52840 reference schematic. We connected a J-Link debugger to the board and are able to successfully...
25 views

0 replies

Started 3 hours ago
by Aditya P
Not Answered
nRF5340+nRF7002: Unable to trigger FOTA download error event after WiFi network disconnected 0

Hi, We have a device using nRF Connect SDK v3.0.2. The issue is when we try to do FOTA download and we disconnect the WiFi network (power down the router AP) while it...
39 views

0 replies

Started 10 hours ago
by Winston A
Not Answered
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board works on DK 0

# nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board -works on DK ## Summary On a custom nRF54L15 board, the PDM peripheral...
38 views

0 replies

Started 14 hours ago
by Cristian Turcan
Not Answered
SPI Master - SCK, MOSI work but CS doesn't 0

Hi, I am using nRF54L15-DK board for development and currently I am trying to talk to an external module via SPI (nRF dev board is the master). I have disabled the external...
- development
- software
- nRF54L15
- spi
32 views

0 replies

Started 15 hours ago
by Unknown Developer

Recent in the DevZone Blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016