Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Wake up after sys_poweroff() via GPIO inconsistent 0

I was doing a demo code to implement a wake up triggered by motion. I was able to make it work with the integrated low power accelerometer on thingy52 but it only worked 1...
7 views

0 replies

Started 11 minutes ago
by yopoitio
Not Answered
Try to build peripheral-uart example for nrf54L15-DK without west 0

Hello at all, I try to compile the example peripheral_uart for the nrf54L15-DK. The goal is to compile without west. My directory structure: where I copied everything from...
15 views

0 replies

Started 1 hour ago
by Neum_d
Not Answered
Is UART1/VCOM1 on nRF9161 used ? 0

Hello, I've a nRF9161DK board and I would like to connect a UART to an external device. Looking at the schematics I see that both UART0 and UART1 of nRF9161 are connected...
14 views

0 replies

Started 1 hour ago
by JOEBRE
Not Answered
Found assembler: arm-zephyr-eabi-gcc.exe. 0

toochain：3.0.2 sdk3.0.2 nrf connect Every time I build, it gets stuck here: Found assembler: C:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi...
17 views

0 replies

Started 1 hour ago
by Liny
Not Answered
basic - how to run first app and get printk output 0

Hello, I know it's a bit basic, but running through all the docs for thingy91:x I got a bit lost. https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/device_guides...
29 views

0 replies

Started 2 hours ago
by smmx

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015